R **ON A/C ALL
Subtask 33-48-13-910-050
A. Preparation for Installation
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Clean the lens (6) with a clean, soft, lint-free cloth.
Subtask 33-48-13-420-051
B. Installation of the Tail Cone Strobe-Light (19LV)
(1)
Install the flash tube assembly (9) with the screws (8).
(2)
Install the new gasket (7) and the lens (6) with the screws (5).
(3)
Apply SPECIAL MATERIALS (Material No. 05-002) to the washers (2) and the screws (1).
(4)
Install the tail cone strobe-light (4) in the tail navigation light
(3)
with the washers (2) and the screws (1).
Subtask 33-48-13-410-051
C. Close Access
(1)
Install the tail navigation light (3) (Ref. TASK 33-41-15-400-001).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 33-48-13-710-050
D. Do the test of the tail cone strobe-light (19LV) WARNING : DO NOT LOOK DIRECTLY AT THE LIGHT FLASH DURING THE TEST.
_______ SUPPLY A COVER, OR SHIELD, TO GIVE PROTECTION FROM THE LIGHT FLASH TO PERSONS IN THE TEST AREA.
(1) Do the operational test of the anticollision/strobe light system (Ref. TASK 33-48-00-710-002). ________
5. Close-up
Subtask 33-48-13-410-050
A. Close Access
(1)
Put the system back to the serviceable condition.
(2)
Remove the access platform(s).
LIGHT - STROBE, WING TIP (16LV,17LV) - REMOVAL/INSTALLATION
___________________________________________________________
TASK 33-48-14-000-001
Removal of the Strobe Light
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : DO NOT TOUCH THE STROBE LIGHTS FOR AT LEAST 5 MINUTES AFTER
_______ OPERATION. THE STROBE LIGHT WILL STILL BE HOT.
WARNING : DO NOT REMOVE THE STROBE LIGHT FOR AT LEAST TEN MINUTES AFTER YOU
_______ DE-ENERGIZE THE ELECTRICAL CIRCUITS. THE HIGH VOLTAGE ELECTRICAL CURRENT IN THE CAPACITOR OF THE STROBE LIGHT IS DANGEROUS.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific access platform 4.35 m (14 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-37-12-000-001 Removal of the Navigation Light Glazing Panel 33-48-14-991-001 Fig. 401
3. Job Set-up
__________
(Ref. Fig. 401/TASK 33-48-14-991-001) Subtask 33-48-14-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in the cockpit on panel 25VU to tell persons not to operate the navigation lights or the strobe lights.
Subtask 33-48-14-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(56)
