_____________________________________________
TASK 33-46-11-000-001
Removal of the Take Off Light (7LR)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______
AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
33-46-11-991-001-A Fig. 401
**ON A/C 051-051,
33-46-11-991-001 Fig. 401A **ON A/C ALL
3. Job Set-up
__________
Subtask 33-46-11-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/TO 3LR W07
4. Procedure
_________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401/TASK 33-46-11-991-001-A)
**ON A/C 051-051,
(Ref. Fig. 401A/TASK 33-46-11-991-001)
**ON A/C ALL
Subtask 33-46-11-020-050
A. Removal of the Take Off Light
(1)
Disconnect the electrical connector (12) from the socket (11).
(2)
Put the blanking caps on the disconnected electrical connector (12) and the socket (11).
(3)
Remove the nut (6), the washer (7), the screw (9) and the washer (8).
(4)
Remove the nuts (5), the washers (4), the screws (1) and the washers (2). During this operation, hold the light (10).
(5)
Remove the light (10) from its support (3).
Take Off Light Figure 401/TASK 33-46-11-991-001-A
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 33-46-11Page 403 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R Take Off Light
R Figure 401A/TASK 33-46-11-991-001
R 1EFF : 051-051, 1 33-46-11 Page 404
1 1 May 01/05
1 1
1CES 1
TASK 33-46-11-400-001
Installation of the Take Off Light (7LR)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
33-46-00-710-001 Operational Test of the Taxi and Take Off Lights 33-46-11-730-001 Adjustment of the Take Off Light (7LR)
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
33-46-11-991-001-A Fig. 401
**ON A/C 051-051,
33-46-11-991-001 Fig. 401A **ON A/C ALL
3. Job Set-up
__________
Subtask 33-46-11-865-051
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(23)
