Subtask 33-48-36-010-050
C. Get Access
(1)
Put the stepladder in position at the applicable location.
(2)
Remove the center ceiling panel 241CC to get access to the power supply unit (1) (Ref. TASK 25-23-41-000-001).
4. Procedure
_________
(Ref. Fig. 401/TASK 33-48-36-991-001) Subtask 33-48-36-020-050
A. Removal of the Power Supply Unit
(1)
Remove and discard the lockwire from the electrical connector (5). WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2
_______ MINUTES AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
(2)
Disconnect the electrical connectors (2) and (5) from the power supply unit (1).
(3)
Put blanking caps on the disconnected electrical connectors.
(4)
Remove the screws (4) and the washers (3).
(5)
Remove the power supply unit (1) from the fuselage.
Power Supply Unit 3LV
Figure 401/TASK 33-48-36-991-001
1EFF : ALL 1 33-48-36 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 33-48-36-400-001
Installation of the Power Supply Unit 3LV
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific stepladder 1.5 m (4 ft. 11 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R No specific Material No. 16-003 lockwire - corrosion resistant steel 0.6mm (0.24 in.) dia. F ASNB70720 COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R 20-28-00-912-004 25-23-41-400-001 33-48-00-710-001 33-48-36-991-001 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not includes the tanks)-Installation of the Ceiling PanelsOperational Test of the Anti-Collision/Strobe LightingFig. 401
3. Job Set-up
__________ Subtask 33-48-36-860-051
A. Aircraft Maintenance Configuration
(1)
Make sure that the switch 2LV BEACON ON-OFF on the overhead panel 25VU is in the OFF position.
(2)
Make sure that the switch 4WL EMER EXIT LT OFF-ARM-ON on the overhead panel 25VUis in the OFF position.
(3)
Make sure that the pushbutton EMERG LIGHT on the FWD Attendant Panel (FAP) is in the released position.
(4)
Make sure that the stepladder is in position at the applicable position.
(5) Make sure that the center ceiling panel 241CC is removed. Subtask 33-48-36-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/BEACON/UPPER 1LV U06
4. Procedure
_________
(Ref. Fig. 401/TASK 33-48-36-991-001) Subtask 33-48-36-420-050
A. Installation of the Power Supply Unit
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Put the power supply unit (1) in position on the fuselage.
(4)
Install the power supply unit (1) with the screws (4) and the washers
(3) and tighten.
(5)
Apply STRUCTURE PAINTS (Material No. 16-003) on one of the screws (4)
(Ref. TASK 20-28-00-912-004).
(6)
Remove the blanking caps from the electrical connectors.
(7)
Make sure that the electrical connectors are clean and in the correct condition.
(8)
Connect the electrical connectors (2) and (5) to the power supply unit (1).
(9)
Safety the electrical connector (5) with lockwire - corrosion resistant steel 0.6mm (0.24 in.) dia..
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(61)
