4. Procedure
_________ Subtask 33-46-00-710-050
A. Operational test of Lights
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the panel 25VU: On the nose landing gear:
-
set the NOSE selector switch to - the taxi light comes on,
TAXI,
-
set the NOSE selector switch to - the taxi and take off lights come on, TO,
-
set the NOSE selector switch to - the taxi and take off lights go off. OFF.
5. Close-up
________ Subtask 33-46-00-862-051
A. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R **ON A/C 051-051,
R TASK 33-46-00-730-001
R Adjustment of the Light Mounts
R 1. Reason for the Job__________________
R To make sure that the light mounts are parallel to the aircraft centerline.
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R 98D33403503000 1 ADJUSTING TOOL - TAKE-OFF/TAXI LIGHTS
R B. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening
R 32-22-00-410-001 Nose Gear Doors - Ground Doors Closing
R 33-46-11-000-001 Removal of the Take Off Light (7LR)
R 33-46-11-400-001 Installation of the Take Off Light (7LR)
R 33-46-12-000-001 Removal of the Taxi Light (8LR)
R 33-46-12-400-001 Installation of the Taxi Light (8LR)
R 33-46-00-991-001 Fig. 501
R 3. Job Set-up__________
R Subtask 33-46-00-010-050
R A. Open the Main Doors of the Nose Gear (Ref. TASK 32-22-00-010-001).
R 4. Procedure_________
R Subtask 33-46-00-820-050
R A. Adjustment of the Light Mounts
R (Ref. Fig. 501/TASK 33-46-00-991-001)
R (1) Remove the taxi light (8LR) (Ref. TASK 33-46-12-000-001) and the take
R off light (7LR) (Ref. TASK 33-46-11-000-001).
R (2) Loosen the 3 screws (1) of the two light mounts.
R (3) Install the tool ADJUSTING TOOL - TAKE-OFF/TAXI LIGHTS
R (98D33403503000)
R - put the sleeve (3) in position on the upper fork of the right mount
R and lock it with the needle (2),
R - put the tooling assembly (4) (slide rod and sleeve) in position on
R the upper fork of the left mount and lock it with the needle (2),
R - put the index (5) against the vertical web of the mount.
R (4) Move the rod of the tooling assembly (4) laterally. The rod must
R slide freely from the left sleeve to the right sleeve.
R (5) Tighten the 3 screws (1) on the two light mounts.
R (6) Make sure that you can turn the rod freely in the two sleeves.
R (7) Remove the right and left needles (2), then remove the sleeve (3) and
R tooling assembly (4) .
R (8) Install the taxi light (8LR) (Ref. TASK 33-46-12-400-001) and the
R take off light (7LR) (Ref. TASK 33-46-11-400-001).
R 5. Close-up________
R Subtask 33-46-00-410-050
R A. Close the Main Doors of the Nose Gear (Ref. TASK 32-22-00-410-001).
R Adjustment of the Taxi Light and Take Off Light Mounts R Figure 501/TASK 33-46-00-991-001 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(22)
