R 1EFF : 051-052, 1 52-31-21Page 450 1 1 May 01/05 1 1 1CES 1
R (3) Disconnect the linkage (3) from the link lever (10) as follows:
R (a) Remove and discard the cotter pin (7) from the nut (6).
R (b) Remove the nut (6), the washer (5), the bush (4) and the bolt (1)
R from the link lever (10).
R (c) Remove the lower eye end of the linkage (3) from the fork end of
R the link lever (10).
R (4) Disassemble the different components from the safety shaft (11) as
R follows:
R (a) Remove the nuts (9), the washers (8) and the tapered pins (2)
R from the safety cams (12),(13).
R (b) Remove the nuts (9), the washers (8) and the tapered pins (2)
R from the link lever (10), the drift pin levers (20) and the vent
R door lever (21).
R (c) Move the vent door lever (21) and the link lever (10) from the
R end of the safety shaft (11).
R (5) Remove the safety shaft (11) from the cargo door structure as
R follows:
R (a) Move the safety shaft (11) slowly in the forward direction
R through the lateral cutout of the cargo door.
R NOTE : Support the safety cams (12),(13) and the drift pin levers____
R (20) during this movement.
R (b) Remove the safety cams (12),(13) and the drift pin lever (20)
R while you remove the safety shaft (11) from the sliding bearing
R (of each frame forkend).
R 1EFF : 051-052, 1 52-31-21Page 451 1 1 May 01/05 1 1 1CES 1
R Safety Shaft Assembly
R Figure 405/TASK 52-31-21-991-004- 12 (SHEET 1)
R 1EFF : 051-052, 1 52-31-21Page 452 1 1 May 01/05 1 1 1CES 1
R Safety Shaft Assembly
R Figure 405/TASK 52-31-21-991-004- 22 (SHEET 2)
R 1EFF : 051-052, 1 52-31-21Page 453 1 1 May 01/05 1 1 1CES 1
R TASK 52-31-21-400-004 R Installation of the Safety Shaft Assembly R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________ R A. Fixtures, Tools, Test and Support Equipment R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION R -------------------------------------------------------------------------------R No specific access platform 3.5 m (11 ft. 6 in.)
R B. Consumable Materials R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R Material No. 04-004 R R R Material No. 15-005 R R R Material No. 15-006 R R
R C. Expendable Parts USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00) AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00) AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
R -------------------------------------------------------------------------------R FIG.ITEM |DESIGNATION |IPC-CSN R -------------------------------------------------------------------------------
R 7 cotter pin 52-31-21 02 -010 R 18 cotter pin 52-31-21 20B-010 R 26 cotter pin 52-31-21 07 -040
R 1EFF : 051-052, 1 52-31-21Page 454 1 1 May 01/05 1 1 1CES 1R D. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門4(100)
