1EFF : ALL 1 52-31-00Page 538 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 52-31-00Page 539 1 1 May 01/05 1 1 1CES 1 Subtask 52-31-00-410-051
R (4) Turn the locking handle to the LOCKED position and push it in the
R recess of the handle flap.
R (5) Do this test:
R NOTE : If necessary, adjust the position of the extended and____
R retracted drift pins (Ref. TASK 52-31-11-820-002).
R -------------------------------------------------------------------------------
R ACTION RESULT
R -------------------------------------------------------------------------------
R 1. On the cargo door: On the cargo door:
R - measure the offset between the - the offset between the parallel
R center lines of the bellcrank center lines must be between 1.0 mm
R and the extended drift pin. (0.0393 in.) and 1.5 mm (0.0590 in.).
R - pull the locking handle away - the drift pins retract and the
R from the recess of the handle locking hooks are in the released
R flap and turn it down to the position.
R UNLOCKED position.
R - measure the distance between - the maximum length of the retracted
R the edge member of the cargo drift pins can be 2.5 mm (0.0984
R door structure and the end of in.).
R the retracted drift pins.
R R (6) Install the door lining (Ref. TASK 52-31-13-400-001) when the test is completed.
R R (7) Make sure that the cargo door is correctly closed and locked (Ref. TASK 52-30-00-860-002).
R **ON A/C ALL
5. Close-up________
Subtask 52-31-00-860-054
A. Put the aircraft back to the serviceable condition.
(1) Make sure that the aircraft electrical circuits are de-energized (Ref. TASK 24-41-00-862-002).
(2) Make sure that the Yellow auxiliary hydraulic system is depressurized (Ref. TASK 29-24-00-864-001).
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make sure that the access panel 134AR is closed.
(3)
Make sure that the access panel 825AR is installed.
(4)
Remove the access platform(s).
1EFF : ALL 1 52-31-00Page 540 1 1 May 01/05 1 1 1CES 1 DOOR - CARGO COMPARTMENT - REMOVAL/INSTALLATION
_______________________________________________
TASK 52-31-11-000-001
Removal of the FWD Cargo-Compartment Door
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific crane with a minimum capacity 130.0 kg (286.6 lb) No specific masking material No specific access platform 3.5 m (11 ft. 6 in.) 98A52307529001 1 SLING - CARGO DOORS 98D52307523000 1 EXTRACTOR - HINGE PINS, CARGO DOOR 98D52307523001 1 EXTRACTOR - HINGE PINS, CARGO DOOR 98D52307524000 1 SUPPORT STRUT - CARGO DOORS
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump
52-31-24-000-001 Removal of the Wiring Harness 4611VB
52-31-11-991-001 Fig. 401
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
52-31-11-991-002 Fig. 402
1EFF : ALL 1 52-31-11Page 401 1 1 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 051-052,
R R 52-31-11-991-002-A **ON A/C ALL
52-31-11-991-003 3. Job Set-up__________ Subtask 52-31-11-010-050 A. Get Access
Fig. 402A
Fig. 403
(1)
Open the FWD cargo compartment door (Ref. TASK 52-30-00-860-001) and safety it with the SUPPORT STRUT - CARGO DOORS (98D52307524000).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(42)
