R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B433 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (3) Disconnect the bellcrank (215) from the bellcrank lever (234) as follows:
 (a)
 Remove and discard the cotter pin (223) from the nut (224).

 (b)
 Remove the nut (224), the washers (233) and the bolt (232) from the upper fork-end of the bellcrank lever (234).

 (c)
 Remove the bushes (235) and (236) from the upper fork-end of the bellcrank lever (234).

 (d)
 Remove the bellcrank (215) from the linkage (234).

 (e)
 Remove the sleeve (240) from the bellcrank (215).

R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B434 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 TASK 52-31-21-400-013

 Installation of the Latching Unit
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00) Material No. 15-005 AIB TN 10138 TYPE I GRADE 2
 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
 (Ref. 20-31-00) Material No. 15-006 AIB TN 10138 TYPE I GRADE 3
 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
 (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
172 cotter pin 52-31-21 34 -240 203 cotter pin 52-31-21 34 -150 206 cotter pin 52-31-21 34 -030 221 cotter pin 52-31-21 40 -040 223 cotter pin 52-31-21 40 -040 225 cotter pin 52-31-21 40 -040
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B435 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 D. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-22-52-640-002 Lubrication of the FWD and AFT Cargo-Compartment Doors 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
 Yellow Electric Pump 52-31-00-720-001 Functional Test of the FWD Cargo-Compartment Door 52-31-11-820-002 Adjustment of the Door Mechanism 52-31-21-991-019 Fig. 418
 3. Job Set-up
__________
 Subtask 52-31-21-860-067
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the FWD cargo-compartment door (referred to as cargo door) is opened and safetied with the actuator safety locks (Ref. TASK 52-30-00-860-001).

 (2)
 Make sure that the access platform in position below the opened cargo door.

 (3)
 Make sure that the access panel 825AR is removed from the cargo door.

 Subtask 52-31-21-865-084
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/HYD POWER/Y 3803GX N30 122VU DOORS/CARGO 1MJ T12 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page B436 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 418/TASK 52-31-21-991-019) Subtask 52-31-21-910-064
 A. Preparation for Installation
 (1)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (2)
 Clean the component interface and/or the adjacent area.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Apply a layer of COMMON GREASE (Material No. 04-004) to:

 -
the inner and outer sliding surfaces of the sleeves (211),(214),(229),(240),

 -
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(150)