R  **ON A/C 001-049, 053-099, 101-105, 151-199, 201-220, 
R  Subtask 52-31-21-560-055-A 
R  B. Preparation for Replacement Component 
R  (1) Make sure that there are new tab washers (371) on the link assy (88). 
R  (2) If not, replace the tab washers (371) as follows: 
R  (a) Release the tab washers (371) from the jam nuts (372). 
R  (b) Remove the lower and top fork ends (95) and (99) from the 
R  connection rod (88). 
R  (c) Remove and discard the tab washers (371) from the connection rod 
R  (88). 
R  (d) Apply COMMON GREASE (Material No. 04-004) to the threaded ends of 
R  the connection rod (88). 
R  (e) Install new tab washers (371) and the two fork ends (95) and (99) 
R  on the connection rod (88). 
R  (3) Make sure that the length between the two fork ends (95) and (99) of 
R  the replacement link assy (88) is as written down before. 
R  Subtask 52-31-21-420-058-A 
R  C. Installation of the Switch Mechanism 
R  (Ref. Fig. 411/TASK 52-31-21-991-009) 
R  (1) Install the link assy (88) as follows: 
R  (a) Install the upper fork-end (99) on the drive shaft lever (102) as 
R  follows: 
R  1 If removed, install the sleeve (100) into the fork-end (99)._ 
R  2 Put the fork end (99) in position to the drive shaft lever_ 
R  (102) and install the bolt (101), the washer (98) and the nut 
R  (97). 
R  3 Tighten the nut (97) and safety it with the new cotter pin_
 (96).

R  (b) Install the lower fork-end (95) to the target lever (90) as 
R  follows: 
R  1_  If removed, install the bush (94) into the fork-end (95).
R  2_  Put the lower fork end (95) to the target lever (90) and
R  install the bolt (89), the washer (93) and the nut (92). 
R  3_ Tighten the nut (92) and safety it with the new cotter pin
 (91). 
R  (2) Install the target lever (3) as follows: 
R  (a) If removed, install the target (365) with the bolts (366), the 
R  washers (363) and the nuts (362) on the target arm (364). 
R  (b) Install the target lever (90) as follows: 
R  1_  Put the target lever (90) on the support fitting (361) and
R  attach it with the washer (369) and the nut (368). 
R  2_ Tighten the nut (368) and safety it with the new cotter pin
 (367). 
R  (c) Install the lower fork end (95) to the target lever (90) (refer 
R  procedure (1) (b)). 
R  Subtask 52-31-21-820-054-A 
R  D. Adjustment Procedure 
R  (1) Push the door handle correctly into the recess of the door structure. 
R  (2) Measure the clearance between the target (365) and the related sensor 
R  (373) of the door sill area. 
R  NOTE : The clearance must be between 1.5 mm (0.0590 in.) and 2.0 mm____
 (0.0787 in.). 
R  (3) If the clearance is out of tolerance, adjust the length of the link 
R  assy (88) as follows: 
R  (a) Turn the connection rod (370) until the clearance is correct. 
R  (b) Make sure that the connection rod (370) is correctly engaged with 
R  the lower and upper fork end (95) and (99).

R  (c) Tighten the jam nuts (372) and safety them with the new tab 
R  washers (371). 
R  (4) Examine the correct function of the proximity switch 32WV (Ref. TASK 
R  52-71-00-820-003). 
R  **ON A/C 051-052, 
R  Subtask 52-31-21-560-055 
R  B. Preparation for Replacement Component 
R  (1) Make sure that there are new tab washers (11) on the link assy (19). 
R  (2) If not, replace the tab washers (11) as follows: 
R  (a) Release the tab washers (11) from the jam nuts (12). 
R  (b) Remove the lower and top fork ends (10),(14) from the connection 
R  rod (13). 
R  (c) Remove and discard the tab washers (11) from the connection rod 
R  (13). 
R  (d) Apply COMMON GREASE (Material No. 04-004) to the threaded ends of 
R  the connection rod (13). 
R  (e) Install new tab washers (11) and the two fork ends (10),(14) on 
R  the connection rod (13). 
R  (3) Make sure that the length between the two fork ends (10),(14) of the 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(129)