(b) Connect the lower fork-end of the control rod (35) to the cover assy (36) as follows:
1 Put the control rod (35) in position and attach it with the
_ bolt (31), the washers (32) and the nut (33).
2 Safety the nut (33) with the new cotter pin (34).
_
(5) Remove the rigging pin (30) from the bellcrank lever (37).
(6) Remove the rigging pin (38) from the bellcrank lever (40). R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-31-21-720-056
D. Do a functional test of the locking mechanism to make sure that the drift pins operate satisfactorily. (Ref. TASK 52-31-00-720-001)
**ON A/C 051-052,
Subtask 52-31-21-720-056-A
D. Do a functional test of the safety mechanism to make sure that the drift pins operate satisfactorily. (Ref. TASK 52-31-00-720-001)
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
Subtask 52-31-21-820-051
E. Adjustment of the the Drift Pin Mechanism
(1) Set the drift pins in their fully extended position as follows:
(a)
Press the roller lever of the interlock mechanism outboard to release the blockage of the door handle.
(b)
Move the door handle down to the locked position and push it into the recess of the door structure.
1EFF : ALL 1 52-31-21Page A436 1 1 Aug 01/05 1 1 1CES 1
(2) Measure the distance between the edge member of the cargo door and
the end of the extended drift pin.
NOTE : The distance must be between 37.7 mm (1.4842 in.) and 34.7 mm____
(1.3661 in.).
(3) If the distance is not correct, adjust the length of the control rod
(328) (Ref. TASK 52-31-11-820-002).
(4) Pull the door handle away from the recess of the door structure to
retract the drift pins.
R **ON A/C 051-052,
R Subtask 52-31-21-820-051-B
R E. Adjustment of the the Drift Pin Mechanism
R (1) Set the drift pins in their fully extended position as follows:
R (a) Press the roller lever of the interlock mechanism outboard to
R release the blockage of the locking handle.
R (b) Turn the locking handle up to the locked position and push it
R into the recess of the handle flap.
R (2) Measure the distance between the edge member of the cargo door and
R the end of the extended drift pin.
R NOTE : The distance must be between 35.7 mm (1.4055 in.) and 36.7 mm____
R (1.4448 in.).
R (3) If the distance is not correct, adjust the length of the Teleflex
R controls (Ref. TASK 52-31-11-820-002).
R (4) Pull the locking handle away from the recess of the handle flap to
R retract the drift pins.
R (5) Measure the distance between the edge member of the cargo door and
R the end of the retracted drift pins.
R NOTE : The distance must be between 0.2 mm (0.0078 in.) and 1.2 mm____
R (0.0472 in.).
R (6) If the distance is not correct, adjust the stop bolt of the lever
R mechanism (Ref. TASK 52-31-11-820-002).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-31-21Page A437 1201-220, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 221-299, 301-399, 401-499,
Subtask 52-31-21-820-051-A
E. Adjustment of the the Drift Pin Mechanism
(1)
Set the drift pins in their fully extended position as follows:
(a)
Press the roller lever of the interlock mechanism outboard to release the blockage of the door handle.
(b)
Move the door handle down to the locked position and push it into the recess of the door structure.
(2)
Measure the distance between the edge member of the cargo door and the end of the extended drift pin.
NOTE : The distance must be between 32.5 mm (1.2795 in.) and 35.5 mm
____
(1.3976 in.).
(3)
If the distance is not correct, adjust the door mechanism (Ref. TASK 52-31-11-820-002).
(4)
Pull the door handle away from the recess of the door structure to retract the drift pins.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(124)
