R 1EFF : 051-052, 1 52-31-21Page 408 1 1 May 01/05 1 1 1CES 1
R (b) Install the bolt (26), the bush (24), the washer (23) and the nut
R (22) on the link rod (17).
R (c) Tighten the nut (22) and safety it with the new cotter pin (21).
R (3) Install the linkage (6) on the link lever (11) of the safety shaft as
R follows:
R (a) Put the eye end (5) in the fork end of the link lever (11).
R (b) Install the bolt (12), the bush (10), the washer (9) and the nut
R (8) on the link lever (11).
R (c) Tighten the nut (8) and safety it with the new cotter pin (7).
R (4) Connect the spring (1) on the recess bush (2) of the link/lever
R connection.
R (5) Install the target of the proximity switch 28WV on the end of the
R replaced locking handle (Ref. TASK 52-71-12-400-001).
R Subtask 52-31-21-820-052
R D. Adjustment of the Locking Handle Mechanism
R (1) Adjust the locking handle to make sure that it operates satisfactory
R (Ref. TASK 52-31-11-820-002).
R (2) Make sure that the gap between the target and the sensor of the
R proximity switch is correctly adjusted (Ref. TASK 52-71-00-820-004).
R Subtask 52-31-21-865-052
R E. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R 1MJ, 3801GX, 3802GX, 3803GX.
R Subtask 52-31-21-720-050
R F. Test Procedure
R (1) Make sure that the locking handle mechanism is correctly lubricated
R (Ref. TASK 12-22-52-640-002).
R (2) Do a functional test to make sure that the force necessary to operate
R the locking handle is correct (Ref. TASK 52-31-00-720-001).
R 1EFF : 051-052, 1 52-31-21Page 409 1 1 May 01/05 1 1 1CES 1
R (3) Make sure that the proximity switch 28WV operates satisfactory
R (Ref. TASK 52-31-00-710-001).
R 5. Close-up________
R Subtask 52-31-21-410-050
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE
R PRESERVATION (Material No. 15-006) to all the components of the
R locking handle mechanism and to the adjacent cargo door structure.
R (3) Install the access panel 825AR on the cargo door.
R (4) Remove the actuator safety locks and close the cargo door (Ref. TASK
R 52-30-00-860-002).
R (5) Remove the access platform(s).
R 1EFF : 051-052, 1 52-31-21Page 410 1 1 May 01/05 1 1 1CES 1
R TASK 52-31-21-000-002 R Removal of the Handle Flap Mechanism R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s)
R No specific access platform 3.5 m (11 ft. 6 in.)
R B. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 52-30-00-860-001 R R 52-31-21-991-002
R 3. Job Set-up
__________ R Subtask 52-31-21-010-051 R A. Get Access
Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump Fig. 402
R (1) Open the FWD cargo-compartment door (referred to as cargo door) and R safety it with the actuator safety locks (Ref. TASK 52-30-00-860-R 001).
R (2) Put the access platform in position at the opened cargo door.
R (3) Remove the access panel 825AR to get access to the attachment screws R of the handle flap mechanism.
R 1EFF : 051-052, 1 52-31-21Page 411 1 1 May 01/05 1 1 1CES 1
R Subtask 52-31-21-865-053
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(88)
