Subtask 52-31-24-820-050
B. Adjustment Procedure
(1) Measure the distance "X" between the lining and the wiring harness (1).
NOTE : The distance "X" must be less 70.0 mm (2.7559 in.).
____
(2)
If the distance "X" is more than allowed, loosen the clamp (16) and move the wiring harness (1) inboard as required.
(3)
Close and open the cargo door (Ref. TASK 52-30-00-860-001) and (Ref. TASK 52-30-00-860-002).
(4)
Make sure that the distance "X" is correct.
5. Close-up
________ Subtask 52-31-24-865-052
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 3801GX, 3802GX, 3803GX.
Subtask 52-31-24-410-050
B. Close Access
(1)
Install the removed door lining (Ref. TASK 52-31-13-400-001).
(2)
Remove the access platform(s).
(3)
Close and lock the cargo door correctly (Ref. TASK 52-30-00-860-002).
1EFF : ALL 1 52-31-24Page 408 1 1 Feb 01/99 1 1 1CES 1
ACTUATOR AND STOP FITTINGS - REMOVAL/INSTALLATION
_________________________________________________ TASK 52-31-31-000-001 Removal of the Stop Bolts
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-31-31-991-001 Fig. 401
3. Job Set-up
__________ Subtask 52-31-31-010-050
A. Get Access
(1)
Open the FWD cargo-compartment door (referred to as cargo door) and safety it with the actuator safety locks (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position below the opened cargo door.
1EFF : ALL 1 52-31-31Page 401 1 1 Feb 01/98 1 1 1CES 1 Subtask 52-31-31-865-053
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU DOORS/CARGO 1MJ T12
4. Procedure
_________ Subtask 52-31-31-020-050
A. Removal of the Stop Bolts
(Ref. Fig. 401/TASK 52-31-31-991-001)
(1)
Release the tab washers (3) which safety the nuts (2).
(2)
Loosen the nuts (2) and remove them with the stop bolts (1) and the tab washers (3).
(3)
Discard the tab washers (3).
1EFF : ALL 1 52-31-31Page 402 1 1 Feb 01/98 1 1 1CES 1
Stop Bolts
Figure 401/TASK 52-31-31-991-001
1EFF : ALL 1 52-31-31 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 52-31-31-400-001
Installation of the Stop Bolts
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-011 Material No. 09-019 Material No. 15-005 USA MIL-G-4343 SILICONE GREASE PNEUMATIC SYST AND SEALS (Ref. 20-31-00)USA AMS 3267/3 LOW ADHESION CORROSION INHIBITING SEALANT (Ref. 20-31-00)AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
R C. Expendable Parts
R R R -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(158)
