(b)
Install the target lever (3) as follows: 1 Put the target lever (3) on the support fitting (9) and
_ install the washer (8) and the nut (7).
2 Tighten the nut (7) and safety it with the new cotter pin (6).
_ (b)).
Subtask 52-31-21-820-054-B
D. Adjustment Procedure
(1)
Push the door handle correctly into the recess of the door structure.
(2)
Measure the clearance between the target (3) and the related sensor
(27) of the door sill area.
NOTE : The clearance must be between 1.5 mm (0.0590 in.) and 2.0 mm
____ (0.0787 in.).
(3) If the clearance is in the limits, tighten the jam nuts (17) and safety them with the new tab washers (16).
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-31-21Page A460 1 1 Aug 01/05 1 1 1CES 1
(4)
If the clearance is not in the limits, adjust the length of the link assy (26) as follows:
(a)
Turn the connection rod (18) until the clearance is correct.
(b)
Make sure that the connection rod (18) is correctly engaged with the two fork-ends (15) and (25).
(c)
Tighten the jam nuts (17) and safety them with the new tab washers (16).
(5)
Make sure that the proximity switch 32WV (Ref. TASK 52-71-00-820-003) functions correctly.
**ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-31-21-410-066
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to all the components of the switch mechanism and to the adjacent cargo door structure.
(3)
Install the access panel 825AR on the cargo door.
(4)
Make sure that the cargo door is correctly closed and door handle is in the LOCKED position (Ref. TASK 52-30-00-860-002).
(5)
Remove the access platform(s).
1EFF : ALL 1 52-31-21Page A461 1 1 Aug 01/05 1 1 1CES 1 1EFF : 051-052, 1 52-31-21Page A462 1 1 May 01/05 1 1 1CES 1R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
R **ON A/C 051-052,
R Subtask 52-31-21-410-066-A
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE
R PRESERVATION (Material No. 15-006) to all the components of the
R switch mechanism and to the adjacent cargo door structure.
R (3) Install the access panel 825AR on the cargo door.
R (4) Make sure that the cargo door is correctly closed and locking handle
R is in the LOCKED position (Ref. TASK 52-30-00-860-002).
R (5) Remove the access platform(s).
TASK 52-31-21-000-010
Removal of the Door Handle Assembly and the Related Linkage Mechanism
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific mounting nut (e.g. NAS 509-4)
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
52-31-21-991-021 Fig. 412 R **ON A/C 106-149, 221-299, 301-399, 401-499,
52-31-21-991-021-A Fig. 412A
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
52-31-21-991-015 Fig. 413
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-21Page A463 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門4(131)
