R (d) Install the bush (24), the screw (23) the washer (22) and the
R castle nut (21) on the lower fork end (10).
R (e) Tighten the castle nut (16) and safety it with the new cotter pin
R (17).
R (f) Tighten the castle nut (21) with the new cotter pin (20).
R (2) Install the target lever (3) as follows:
R (a) Install the target (4) on the target lever (3) with the screws
R (5), the washers (2) and the nuts (1).
R (b) Put the target lever (3) on the support fitting (9) and attach it
R with the washer (8) and the castle nut (7).
R (c) Tighten the castle nut (7).
R (d) Safety the castle nut (7) with the new cotter pin (6).
R (e) Install the lower fork end (10) of the link assy (19) on the
R target lever (3).
R Subtask 52-31-21-820-054
R D. Adjustment Procedure
R (1) Push the locking handle correctly into the recess of the handle flap.
R (2) Measure the clearance between the target (4) and the related sensor
R (26) of the door sill area.
R NOTE : The clearance must be between 1.5 mm (0.0590 in.) and 2.0 mm____
R (0.0787 in.).
R (3) If the clearance is out of tolerance, adjust the length of the link
R assy (19) as follows:
R (a) Turn the connection rod (13) until the clearance is correct.
R (b) Make sure that the connection rod (13) is correctly engaged with
R the lower and top fork end (10),(14).
R (c) Tighten the jam nuts (12) and safety them with the new tab
R washers (11).
(4) Examine the correct function of the proximity switch 30WV with the (Ref. TASK 52-71-00-820-003).
R **ON A/C 106-149, 221-299, 301-399, 401-499,
Subtask 52-31-21-560-055-B
B. Preparation of a Replacement Component
(1)
Make sure that there are new tab washers (16) on the link assy (26).
(2)
If not, replace the tab washers (16) as follows:
(a)
Release the tab washers (16) from the jam nuts (17).
(b)
Remove the two fork-ends (15) and (25) from the connection rod (18).
(c)
Remove and discard the tab washers (16) from the connection rod (18).
(d)
Apply the COMMON GREASE (Material No. 04-004) to the threaded ends of the connection rod (18).
(e)
Install the new tab washers (16) and the two fork-ends (15) and
(25) on the connection rod (18).
(f)
Do not fully tighten the jam nuts (17) or safety them with the tab washers (16) at this time.
(3)
Make sure that the distance between the two fork-ends (15) and (25) of the replacement link assy (26) is the same as you recorded before.
Subtask 52-31-21-420-058-B
C. Installation of the Switch Mechanism
(Ref. Fig. 411B/TASK 52-31-21-991-009-A)
(1) Install the link assy (26) as follows:
(a) Install the upper fork-end (25) on the drive shaft lever (24) as follows:
1 If removed, install the sleeve (22) in the fork-end (25).
_
R 1EFF : 051-052, 106-149, 221-299, 301-399, 1 52-31-21Page A459 1401-499, 1Aug 01/05 1 1 1CES 1
2_ Put the fork-end (25) in position on the drive shaft lever
(24) and install the bolt (23), the washer (21) and the nut
(20).
3_ Tighten the nut (20) and safety it with the new cotter pin
(19).
(b) Install the lower fork-end (15) on the target lever (3) as follows:
1 If removed, install the bush (11) in the fork-end (15).
_ 2 Put the lower fork-end (15) on the target lever (3) and
_ install the bolt (10), the washer (12) and the nut (13).
3 Tighten the nut (13) and safety it with the new cotter pin
_ (14).
(2) Install the target lever (3) as follows:
(a)
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門4(130)
