(b)
Install the bolt (265), the washers (260) and the nut (259) on the interlock fitting.
(c)
Tighten the nut (259) and safety it with the new cotter pin (258).
(5)
Install the pin (271) in the interlock fitting and safety it with the washer (251) and the new cotter pin (252).
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-32-21-820-055
D. Adjustment Procedure
(1)
Adjust the gap between the stop assy (277) and the interlock cam of the latching shaft (Ref. TASK 52-32-11-820-002).
(2)
Make sure that the lock nut (275) is tightened and safetied with the new tab washer (274) after the final adjustment.
Subtask 52-32-21-710-050
E. Operational Test of the Interlock Mechanism
(1)
Make sure that the door handle is in the UNLOCKED position.
(2)
Try to move the door handle in the LOCKED position. NOTE : The stop asy (277) must block the interlock cam of the
____
latching shaft.
(3)
Press the roller lever (263) outboards to release the blockage of the latching shaft.
NOTE : You can push down the door handle to the LOCKED position.
____
(4) Pull up the door handle handle to the UNLOCKED position.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-21Page A406 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 051-052,
Subtask 52-32-21-820-055-A
D. Adjustment Procedure
(1)
Adjust the gap between the stop (25) and the interlock cam of the locking shaft (Ref. TASK 52-32-11-820-002).
(2)
Make sure that the lock nut (27) is tightened and safetied with the new tab washer (28) after the final adjustment.
Subtask 52-32-21-710-050-A
E. Operational Test of the Interlock Mechanism
(1)
Make sure that the locking handle is in the UNLOCKED position.
(2)
Try to move the locking handle in the LOCKED position. NOTE : The stop (25) must block the interlock cam of the locking
____
shaft.
(3)
Press the roller lever (5) outboards to release the blockage of the locking shaft.
NOTE : You can turn the locking handle to the LOCKED position.
____
(4) Turn the locking handle handle to the UNLOCKED position. **ON A/C ALL
5. Close-up
________ Subtask 52-32-21-865-067
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 3801GX, 3802GX, 3803GX.
R 1EFF : ALL 1 52-32-21Page A407 1 1 Aug 01/05 1 1 1CES 1 Subtask 52-32-21-410-056
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply STORAGE PRESERVATION (Material No. 15-005) to all the components of the interlock mechanism and to the adjacent cargo door structure.
(3)
Install the access panel 826AR on the cargo door.
(4)
Remove the actuator safety locks and close the cargo door (Ref. TASK 52-30-00-860-002).
(5)
Remove the access platform(s).
R 1EFF : ALL 1 52-32-21Page A408 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 051-052,
TASK 52-32-21-000-007 Removal of the Locking Unit
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.5 mm (0.1377 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-31-21-000-005 Removal of the Locking Shaft Assembly 52-32-21-991-009 Fig. 409
3. Job Set-up
__________ Subtask 52-32-21-010-057
A. Get Access
(1)
Open the AFT cargo-compartment door (referred to as cargo door) and safety it with the actuator safety locks (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position below opened the cargo door.
(3)
Remove the access panel 826AR from the cargo door.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(101)
