(2)
If not, replace the tab washers (11) as follows:
(a)
Release the tab washers (11) from the jam nuts (12).
(b)
Remove the lower and top fork ends (10),(14) from the connection rod (13).
(c)
Remove and discard the tab washers (11) from the connection rod (13).
R 1EFF : 001-049, 051-099, 101-105, 201-220, 1 52-32-21Page A495 1 1 Aug 01/05 1 1 1CES 1
(d)
Apply COMMON GREASE (Material No. 04-004) to the threaded ends of the connection rod (13).
(e)
Install new tab washers (11) and the two fork ends (10),(14) on the connection rod (13).
(3) Make sure that the length between the two fork ends (10),(14) of the replacement link assy (19) is as written down before.
Subtask 52-32-21-420-065
C. Installation of the Switch Mechanism
(1)
Install the link assy (19) as follows:
(a)
Put the top fork end (14) in position to the shaft lever (18).
(b)
Install the washer (15) and the nut (16) on the threaded pin of the shaft lever (18).
(c)
Tighten the nut (16) and safety it with the new cotter pin (17).
(d)
Put the lower fork end (10) in position to the target lever (3).
(e)
Install the bush (24), the screw (23) the washer (22) and the nut
(21) on the lower fork end (10).
(f)
Tighten the nut (21) and safety it with the new cotter pin (20).
(2)
Install the target lever (3) as follows:
(a)
Install the target (4) on the target lever (3) with the screws (5), the washers (2) and the nuts (1).
(b)
Put the target lever (3) on the support fitting (9) and attach it with the washer (8) and the nut (7).
(c)
Tighten the nut (7) and safety it with the new cotter pin (6).
(d)
Put the lower fork end (10) in position to the target lever (3).
(e)
Install the bush (24), the screw (23) the washer (22) and the nut
(21) on the lower fork end (10).
(f)
Tighten the nut (21) with the new cotter pin (20).
R 1EFF : 051-052, 1 52-32-21Page A496 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 221-299, 301-399, 401-499,
Subtask 52-32-21-560-054-C
B. Preparation of a Replacement Component
(1)
Make sure that there are new tab washers (16) on the link assy (26).
(2)
If not, replace the tab washers (16) as follows:
(a)
Release the tab washers (16) from the jam nuts (17).
(b)
Remove the two fork-ends (15) and (25) from the connection rod (18).
(c)
Remove and discard the tab washers (16) from the connection rod (18).
(d)
Apply the COMMON GREASE (Material No. 04-004) to the threaded ends of the connection rod (18).
(e)
Install the new tab washers (16) and the two fork-ends (15) and
(25) on the connection rod (18).
(f)
Do not fully tighten the jam nuts (17) or safety them with the tab washers (16) at this time.
(3)
Make sure that the distance between the two fork-ends (15) and (25) of the replacement link assy (26) is the same as you recorded before.
Subtask 52-32-21-420-065-C
C. Installation of the Switch Mechanism
(1) Install the link assy (26) as follows:
(a) Install the upper fork-end (25) on the drive shaft lever (24) as follows:
1 If removed, install the sleeve (22) in the fork-end (25).
_ 2 Put the fork-end (25) in position on the drive shaft lever
_ (24) and install the bolt (23), the washer (21) and the nut (20).
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-32-21Page A497 1 1 Aug 01/05 1 1 1CES 1 3 Tighten the nut (20) and safety it with the new cotter pin
_
(19).
(b) Install the lower fork-end (15) on the target lever (3) as follows:
1 If removed, install the bush (11) in the fork-end (15).
_ 2 Put the lower fork-end (15) on the target lever (3) and
_ install the bolt (10), the washer (12) and the nut (13).
3 Tighten the nut (13) and safety it with the new cotter pin
_
(14).
(2) Install the target lever (3) as follows:
(a)
If removed, install the target (4) with the bolts (5), the washers (2) and the nuts (101) on the target lever (3).
(b)
Install the target lever (3) as follows: 1 Put the target lever (3) on the support fitting (9) and
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(124)
