(4) Remove the vertical control rod (317) as follows:
(a) Disconnect the lower fork-end of the connection rod (317) from the drift pin lever (321) as follows:
1 Remove and discard the cotter pin (318) from the nut (319).
_
2 Remove the nut (319), the washers (320) and the bolt (322).
_
3 Disconnect the connection rod (317) from the drift pin lever
_ (321).
R 1EFF : 001-049, 053-099, 101-105, 201-220, 1 52-32-21Page A445 1 1 Aug 01/05 1 1 1CES 1 (b) Disconnect the upper fork-end of the connection rod (317) from the shaft lever (314) as follows:
1_ Remove and discard the cotter pin (323) from the nut (324).
2_ Remove the nut (324), the washers (316) and the bolt (315).
3_ Disconnect the connection rod (317) from the shaft lever
(314).
(5)
Disassemble the bearing housing (329) as follows:
(a)
Remove the rigging pin (311) from the bearing housing (329).
(b)
Remove the nut (347), the spacer (346) and the tapered pin (345) from the bellcrank lever (299).
(c)
Remove the bellcrank lever (299) from the support shaft (344).
(d)
Remove the nut (341), the spacer (342) and the tapered pin (343) from the shaft lever (332).
(e)
Remove the support shaft (344) from the bearing housing (329) and collect the shaft lever (332).
(6)
Disassemble the housing assy (359) as follows:
(a)
Remove the screws (358), the washers (357) and the housing assy
(359) from the beam (349).
(b)
Remove the nut (356), the spacer (355) and the tapered pin (354) from the shaft lever (327).
(c)
Remove the shaft lever (327) and the spacer (353) from the support shaft (348).
(d)
Remove the nut (350), the spacer (351 and the tapered pin (352) from the shaft lever (314).
(e)
Remove the support shaft (348) from the housing (359) and collet the shaft lever (314).
R 1EFF : 001-049, 053-099, 101-105, 201-220, 1 52-32-21Page A446 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 051-052,
Subtask 52-32-21-020-062-C
B. Removal of the Teleflex Controls NOTE : The teleflex controls include the eye ends (37),(18), the upper
____ ball joint (67), the lower ball joint (40) and the ball bearing control (52).
(1)
Disconnect the eye end (37) from the lever (33) of the safety shaft as follows:
(a)
Remove and discard the cotter pin (36) from the nut (35).
(b)
Remove the nut (35), the washers (32) and the bolt (31) from the lever (33).
(c)
Remove the eye end (37) from the lever (33).
(d)
If necessary, remove the bush (34) from the lever (33).
(2)
Disconnect the eye end (18) from the bellcrank lever (16) as follows:
(a)
Remove and discard the cotter pin (24) from the nut (25).
(b)
Remove the nut (25), the washers (26) and the bolt (28) from the bellcrank lever (16).
(c)
Disconnect the eye end (18) from the bellcrank lever (16).
(d)
If necessary, remove the bush (27) from the bellcrank lever (16).
(3)
Disconnect the upper ball joint (67) together with the eye end (18) from the ball bearing control (52) as follows:
(a)
Bend the tab washer (64) and loosen the lock nut (65).
(b)
Remove the upper ball joint (67), the tab washer (64) and the lock nut (65) from the ball bearing control (52).
NOTE : Discard the tab washer (64).
____
(c) Remove the seal nut (62) from the control cable (52).
R 1EFF : 051-052, 1 52-32-21Page A447 1 1 Aug 01/05 1 1 1CES 1
(4) Disconnect the lower ball joint (40) together with the eye end (37) from the ball bearing control (52) as follows:
(a)
Bend the tab washer (41) and loosen the lock nut (42).
(b)
Remove the lower ball joint (40), the tab washer (41) and the lock nut (42) from the control cable (52).
NOTE : Discard the tab washer (41).
____
(c) Remove the seal nut (43) from the control cable (52).
(5)
If necessary, remove the eye ends (18),(37) from the ball joints (67),(40) as follows:
(a)
Bend the tab washers (69),(38) and loosen the lock nuts
(68),(39).
(b)
Remove the eye ends (18),(37), the tab washers (69),(38) and the lock nuts (68),(39) from the ball joints (67),(40). Discard the tab washer.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門5(109)
