曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 Measurement of Fit and Clearances
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 2.3 m (7 ft. 7 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
 Yellow Electric Pump 52-31-11-000-001 Removal of the FWD Cargo-Compartment Door 52-32-11-400-001 Installation of the AFT cargo Compartment Door 52-32-21-000-001 Removal of the Locking Handle Mechanism 52-32-21-000-002 Removal of the Handle Flap Mechanism 52-32-21-400-001 Installation of the Locking Handle Mechanism 52-32-21-400-002 Installation of the Handle Flap Mechanism 52-32-11-991-001 Fig. 608 52-32-11-991-002 Fig. 609 52-32-11-991-003 Fig. 610
 1EFF : 051-052, 1 52-32-11Page 657 1 1 Aug 01/05R 1 1 1CES 1

 3. Job Set-up
__________
 Subtask 52-32-11-860-057
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the AFT cargo compartment door (referred to as cargo door) is closed and locked (Ref. TASK 52-30-00-860-001).

 (2)
 Put the access platform in position below the closed cargo door.

 (3)
 Remove the access panel 826AR from the cargo door.

 (4)
 Disassmble the locking handle mechanisn from the locking shaft (Ref. TASK 52-32-21-000-001).

 (5)
 Remove the handle flap mechanism from the cargo door (Ref. TASK 52-32-21-000-002).

 (6)
 Attach the cargo door to the crane to take the load from the hinge pins (Ref. TASK 52-31-11-000-001).

 4. Procedure
_________
 Subtask 52-32-11-220-050
 A. Measurement of the Deflection Unit
 (Ref. Fig. 608/TASK 52-32-11-991-001)

 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C-C | 7.912 | 7.922 | | | 7.900 | | | | OD 1 |(0.3114) |(0.3118) | | |(0.3110) | | | | | | | 0.008 | 0.033 | | | 0.066 | | | | | (0.0003)| (0.0012)| | |(0.0025)| | C-C | 7.930 | 7.945 | | | | 7.966 | | | ID 2 |(0.3122) |(0.3127) | | | |(0.3136) | | -------------------------------------------------------------------------------
1EFF : 051-052, 1 52-32-11Page 658 1 1 Aug 01/05R 1 1 1CES 1

 Fit and Clearances of the Locking Handle Mechanism
 Figure 608/TASK 52-32-11-991-001

 1EFF : 051-052, 1 52-32-11Page 659 1 1 Aug 01/05R 1 1 1CES 1

 Subtask 52-32-11-220-051
 B. Measurement of the Locking Handle Mechanism
 (Ref. Fig. 608/TASK 52-32-11-991-001)

 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | D-D | 6.336 | 6.345 | | | 6.315 | | | | OD 3 |(0.2494) |(0.2498) | | |(0.2486) | | | | | | | 0.005 | 0.029 | | | 0.071 | | | | | (0.0001)| (0.0011)| | |(0.0027)| | D-D | 6.350 | 6.365 | | | | 6.386 | | | ID 4 |(0.2500) |(0.2505) | | | |(0.2514) | | -------------------------------------------------------------------------------
Subtask 52-32-11-220-052
 C. Measurement of the Handle Flap Mechanism
 (Ref. Fig. 609/TASK 52-32-11-991-002)

 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C-C | 6.336 | 6.345 | | | 6.323 | | | | OD 1 |(0.2494) |(0.2498) | | |(0.2489) | | | | | | | 0.005 | 0.029 | | | 0.063 | | | | | (0.0001)| (0.0011)| | |(0.0024)| | C-C | 6.350 | 6.365 | | | | 6.386 | | | ID 2 |(0.2500) |(0.2505) | | | |(0.2514) | | -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(57)