Door Handle
 Figure 413/TASK 52-32-21-991-014

R 1EFF : 001-049, 053-099, 101-105, 201-220, 1 52-32-21Page B409 1 1 Aug 01/05 1 1 1CES 1

 Door Handle Figure 413A/TASK 52-32-21-991-014-B
R 1EFF : 106-149, 221-299, 301-399, 1 52-32-21Page B410 1 1 Aug 01/05 1 1 1CES 1

 Door Handle
 Figure 413B/TASK 52-32-21-991-014-A 
R 1EFF :  151-199,  1  52-32-21 Page B411 
1  1  Aug 01/05
 1  1
 1CES  1

R  Door Handle 
R  Figure 413C/TASK 52-32-21-991-014-C 
R 1EFF :  401-499,  1  52-32-21 Page B412 
1  1  Aug 01/05
 1  1
 1CES  1

 Linkage Mechanism
 Figure 414/TASK 52-32-21-991-015

R 1EFF : 001-049, 053-099, 101-105, 201-220, 1 52-32-21Page B413 1 1 Aug 01/05 1 1 1CES 1

 Linkage Mechanism Figure 414A/TASK 52-32-21-991-015-B
R 1EFF : 106-149, 221-299, 301-399, 1 52-32-21Page B414 1 1 Aug 01/05 1 1 1CES 1

 Linkage Mechanism
 Figure 414B/TASK 52-32-21-991-015-A 
R 1EFF :  151-199,  1  52-32-21 Page B415 
1  1  Aug 01/05
 1  1
 1CES  1

R  Linkage Mechanism 
R  Figure 414C/TASK 52-32-21-991-015-C 
R 1EFF :  401-499,  1  52-32-21 Page B416 
1  1  Aug 01/05
 1  1
 1CES  1

R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 52-32-21-020-066
 A. Removal of the Door Handle
 (1)
 Make sure that the door handle (14) is in the UNLOCKED position.

 (2)
 Install a mounting nut (e.g. NAS 509-4) (18) on the spring bolt (19) to keep the handle spring (20) in position.

 (3)
 Remove the control rod (57) from the shaft lever (25) as follows:

 (a)
 Remove and discard the cotter pin (61) from the nut (60).

 (b)
 Remove the nut (60), washers (59) and the bolt (58).

 (c)
 Disconnect the fork-end of the control shaft (57) from the shaft lever (25).

 (4)
 Remove the connection rod (45) from the Maltese-cross latch (32) as follows:

 (a)
 Remove and discard the cotter pin (46) from the nut (47).

 (b)
 Remove the nut (47), washers (48) and the bolt (49).

 (c)
 Disconnect the fork-end of the connection rod (45) from the Maltese-cross latch (32).

 (5)
 Remove the door handle (14) from the door structure (17) as follows:

 (a)
 Remove the screws (29) and the lock device (30) from the door structure (17).

 (b)
 Carefully move the door handle shaft (26) in the rear direction.

 (c)
 Remove the door handle (14) and the adjustment washers (15) and

 (16) from the door structure (17) while you remove the door handle shaft (26).
 NOTE : Record the quantity of the adjustment washers (15) and
____
 (16) for easier installation.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-21Page B417 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,

 Subtask 52-32-21-020-067
 B. Removal of the Linkage Mechanism WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE TENSION
_______
 IN THE SPRING CAN CAUSE INJURY TO PERSONS.

 (1)
 Remove the gas spring (27) as follows:

 (a)
 Remove the nut (62), the washer (63) and the bolt (64) from the shaft lever (25).

 (b)
 Remove the nuts (69), the washers (66) and the bolts (65) from the door strucutre (67) and the mounting bracket (68).

 (c)
 Carefully remove the mounting bracket (67) from the door structure (68) and disassemble the shaft lever (25) from the serrated shaft (31).

 (d)
 Remove and discard the cotter pins (22) from the pins (24).

 (e)
 Remove the pins (24) and the washers (23) and (28) to disconnect the gas spring (27) from the shaft lever (25) and the mounting bracket (68).

 (2)
 Remove the serrated shaft (31) from the door structure (38) as follows:

 (a)
 Remove the nut (50), the washer (51) and the bolt (39) and disconnect the spring bolt (19) from the roller lever (33).

 (b)
 Remove the nut (37), the washer (36) and the bolt (35) from the Malteser-cross latch (34).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(128)