R 1EFF : 001-049, 053-099, 101-149, 201-299, 1 52-32-21Page B430 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(c)
Make sure that the attachment holes of the Maltese-cross lock
(34) and the serrated shaft (31) align.
(d)
Attach the Maltese-cross lock (34) with the bolt (35), the washer
(36) and the nut (37) on the serrated shaft (31).
(2)
Install the gas spring (27) between the mounting bracket (67) and the shaft lever (25) as follows:
(a)
Put the gas spring (27) with the washers (28) in position and attach it with the pins (24).
(b)
Safety the pins (24) with the washers (23) and the new cotter pins (22).
(3)
Assemble the shaft lever (25) with the gas spring (27) and the mounting bracket (67) on the serrared shaft (31) as follows:
(a)
Move the shaft lever (25) on the splined end of the serrated shaft (31) until their attachment holes align.
(b)
Attach the shaft lever (25) with the bolt (64), the washer (63) and the nut (62) on the serrated shaft (31).
(4)
Put the mounting bracket (67) in position at the door structure and attach it with the bolts (65), the washers (66) and the nuts (68).
NOTE : You must install the mounting bracket (67) with force to
____
compress the gas spring (27).
(5)
If removed, install the handle spring (20) as follows:
(a)
Install the handle spring (20) on the spring bolt (19).
(b)
Put the spring bolt (19) with the handle spring (20) in position in the door beam 4.
(c)
Install the bush (71), and the mounting nut (18) on the spring bolt (19) to set the handle spring (20) under pre-tension.
(6)
Attach the spring bolt (19) to the roller lever (33) as follows:
(a)
Put the fork-end of the spring bolt (19) in its correct
installation position atthe roller lever (33).
(b)
Install the bolt (39), the washer (51) and the nut (50).
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-32-21Page B431 1 1 Aug 01/05 1 1 1CES 1
(7)
Install the control rod (57) on the locking shaft lever (52) as follows:
(a)
Put the lower fork-end of the control rod (57) in its correct installation position on the locking shaft lever (52).
(b)
Install the bolt (56), the washers (55) and the nut (54).
(c)
Tighten the nut (54) and safety it with the new cotter pin (53).
(8)
Install the connection rod (45) on the link lever (40) as follows:
(a) Put the lower fork-end of connection rod (45) in position and install the bolt (44), the washers (43) and the nut (42).
(b) Tighten the nut (42) and safety it with the new cotter pin (41). **ON A/C 151-199,
Subtask 52-32-21-420-067-A
B. Installation of the Linkage Mechanism
(1)
Install the serrated shaft (31) into the door structure (38) as follows:
(a)
Move the serrated shaft (31) through the lateral cutout of the cargo door into the sliding bearings of the door structure (38).
(b)
During this movement, assemble the Maltese-cross latch (32), the roller lever (33) and the Maltese-cross lock (34) in the correct sequence on the serrated shaft (31).
(c)
Make sure that the attachment holes of the Maltese-cross lock
(34) and the serrated shaft (31) are align.
(d)
Attach the Maltese-cross lock (34) with the bolt (35), the washer
(36) and the nut (37) on the serrated shaft (31).
(2)
Install the gas spring (27) between the mounting bracket (68) and the shaft lever (25) as follows:
(a) Put the gas spring (27) together with the washers (28) in position and attach it with the pins (24).
R 1EFF : 106-149, 151-199, 221-299, 301-399, 1 52-32-21Page B432 1401-499, 1Aug 01/05 1 1 1CES 1
(b) Safety the pins (24) with the washers (23) and the new cotter pins (22).
(3)
Assemble the shaft lever (25) together with the gas spring (27) and the mounting bracket (68) on the serrared shaft (31) as follows:
(a)
Move the shaft lever (25) on the splined end of the serrated shaft (31) until their attachment holes are align.
