(a)
Remove the screws (119) and (120), the washers (118) and the access panel (117) from the inner skin of the cargo door.
(b)
Remove the screws (112) and lock device (113) from the door structure.
(c)
Install a mounting nut (e.g. NAS 509-4) on the spring bolt to keep the handle spring in position.
(d)
Carefully remove the door handle shaft (114) and change the position and/or the quantity of the adjustment washers (115) and (116).
(e)
Assemble the door handle shaft (114) and the adjustment washers
(115) and (116) on the door structure.
(f)
Make sure that the lateral gaps "A" are correctly adjusted.
(g)
Safety the door handle shaft (114) with the lock device (113) and the screws (112).
(h)
Remove the mounting nut from the spring bolt.
(i)
Put the access panel (117) in position to the inner skin and attach it with the washers (118), screws (119) and (120).
(3)
Adjust the offset "B" of the door handle as follows:
(a) Make sure that the door handle is in line with the cargo door structure.
NOTE : It is allowed that the door handle is out of wind for max.
____
1.0 mm (0.0393 in.)
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-11Page 534 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(b) If the offset is out of tolerances, loosen the nut (112) and turn the stop bolt (110) as required.
(c) If the offset "B" is correct, tigthen the nut (112).
Subtask 52-32-11-820-057
R B. Adjustment of the Skin Offset at the Door Handle
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
(Ref. Fig. 504/TASK 52-32-11-991-011)
**ON A/C 106-149, 221-299, 301-399,
(Ref. Fig. 504B/TASK 52-32-11-991-011-A)
R **ON A/C 401-499,
R (Ref. Fig. 504C/TASK 52-32-11-991-011-C)
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
R R (1) Measure the skin offset "C" between the door handle (128) and the access panel (127).
R R NOTE : The skin offset "C" must be between 0.3 mm (0.0118 in.) and____ 0.7 mm (0.0275 in.)
R R (2) If the skin offset "C" is not in the limits, adjust the position of the catch hook (125) as follows:
(a) Remove the screws (124), the catch hook (125) and the shim (126) from the structure fitting (121).
R R (b) Prepare the shim (126) as required until the skin offset "C" is correct.
(c) Attach the catch hook (125) and the shim (126) with the screws (124) on the structure fitting (121).
R (d) Make sure that the skin offset "C" is correctly adjusted.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-11Page 535 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Handle Flap at the Door Handle
Figure 504/TASK 52-32-11-991-011
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-32-11Page 536 1201-220, 1Aug 01/05 1 1 1CES 1
Adjustment of the Handle Flap
Figure 504A/TASK 52-32-11-991-011-B
R 1EFF : 051-052, 1 52-32-11 Page 537
1 1 Aug 01/05
1 1
1CES 1
Adjustment of the Handle Flap of the Door Handle
Figure 504B/TASK 52-32-11-991-011-A
R 1EFF : 106-149, 221-299, 301-399, 1 52-32-11Page 538 1 1 Aug 01/05 1 1 1CES 1R Adjustment of the Handle Flap of the Door Handle R Figure 504C/TASK 52-32-11-991-011-C
R 1EFF : 401-499, 1 52-32-11Page 539 1 1 Aug 01/05 1 1 1CES 1
Subtask 52-32-11-820-058
R C. Adjustment of the Latching Mechanism
R **ON A/C 001-049, 053-099, 101-105, 201-220,
(Ref. Fig. 505/TASK 52-32-11-991-012)
**ON A/C 106-149, 221-299, 301-399,
(Ref. Fig. 505B/TASK 52-32-11-991-012-A)
R **ON A/C 151-199,
R (Ref. Fig. 505C/TASK 52-32-11-991-012-C)
R **ON A/C 401-499,
R (Ref. Fig. 505D/TASK 52-32-11-991-012-D)
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(1) Move the latching units of the open cargo door to the locked condition as follows:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(33)
