(2)
 Connect the connection rod (16) to the drive lever (8) as follows:

 (a)
 Put the fork-end of the connection rod (16) on the drive lever (8).

 (b)
 Install the bolt (6), the washers (7) and the nut (9) at the drive lever (8).

 (c)
 Tighten the nut (9) and safety it with the new cotter pin (10).

 (3)
 Install the connection rod (23) as follows:

 (a)
 Put the connection rod (23) in position and connect the fork-end to the lever (11) with the bolt (15), the washers (14) and the nut (13).

 (b)
 Tighten the nut (13) and safety it with the new cotter pin (12).

 (c)
 Put the connection rod (23) in position and connect the fork-end to the twin lever (19) with the bolt (18), the washers (17) and the nut (21).

 (d)
 Tighten the nut (21) and safety it with the new cotter pin (22).

R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-32-21Page 460 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 151-199,

 Subtask 52-32-21-420-066-A
 D. Installation of the Linkage
 (Ref. Fig. 404C/TASK 52-32-21-991-003-A)

 (1)
 Connect the connection rod (82) to the vent door lever (85) of the safety shaft as follows:

 (a)
 Put the lower eye end of the connection rod (82) on the fork end of the vent door lever (85).

 (b)
 Install the bolt (83), the washers (84) and the nut (86).

 (c)
 Tighten the nut (86) and safety it with the new cotter pin (87).

 (2)
 Connect the connection rod (82) on the lever (80) as follows:

 (a)
 Put the upper eye end of the connection rod (82) on the fork end of the lever (80).

 (b)
 Install the bolt (81), the washers (79) and the nut (78) on the lever (80).

 (c)
 Tighten the nut (78) and safety it with the new cotter pin (77).

 (3)
 Connect the link assy (88) on the drive shaft lever (102) as follows:

 (a)
 Put the fork-end of the link assy (88) on the eye-end of the drive shaft lever (102) and install the bolt (101),the sleeve (100), the washer (98) and the nut (97).

 (b)
 Tighten the nut (97) and safety it with the new cotter pin (96).

 (4)
 Connect the link asssy (88) on the target lever (90) as follows:

 (a)
 Put the fork end of the link assy (88) on the target lever (90) and install the bolt (89), the bush (94), the washer (93) and the nut (92).

 (b)
 Tighten the nut (92) and safety it with the new cotter pin (91).

R 1EFF : 151-199, 1 52-32-21Page 461 1 1 Aug 01/05 1 1 1CES 1

 (5)
 Connect the drawbar (71) on the shaft lever (76) as follows:

 (a)
 Put the eye end of the drawbar (71) into the fork end of the shaft lever (76).

 (b)
 Install the bolt (72), the washers (73) and the nut (74) on the shaft lever (76).

 (c)
 Tighten the nut (74) and safety it with the new cotter pin (75).

 (6)
 Connect the drawbar (71) on the actuator arm (107) of the vent door as follows:

 (a)
 Put the eye end of the drawbar (71) into the fork end of the actuator arm (107).

 (b)
 Install the bolt (108), the washers (105), the bush (106) and the nut (104) on the actuator arm (107).

 (c)
 Tighten the nut (104) and safety it with the new cotter pin (103).

R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 52-32-21-820-052
 E. Adjustment Procedure
 (1)
 Adjust the skin offset of the vent door (Ref. TASK 52-31-11-820-003).

 (2)
 Make sure that the length of the link assy (88) is correctly adjusted (Ref. TASK 52-71-12-400-002).

 **ON A/C 051-052,
 Subtask 52-32-21-820-052-A
 E. Adjustment Procedure
 (1)
 Adjust the skin offset of the vent door (Ref. TASK 52-32-11-820-003).

 (2)
 Make sure that the length of the link assy (44) is correctly adjusted (Ref. TASK 52-71-12-400-002).

R 1EFF : ALL 1 52-32-21Page 462 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 Subtask 52-32-21-720-051
 F. Test Procedure
 (1) Make sure that the proximity switch 32WV operates satisfactorily (Ref. TASK 52-32-00-720-001).
 5. Close-up
________
 **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,

 Subtask 52-32-21-410-052
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(89)