(1)
Prepare the door seal as follows:
(a)
Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR54 and FR54A.
(b)
Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2)
Install the additional silicon tube into the door seal as follows:
(a)
Cut the additional silicon tube (Spec: NSA 3629-8-12) to a length of 3465.0 mm (136.4173 in.)
(b)
Push the seal to open the cut.
(c)
Carefully introduce the additional silicon tube into the door seal.
(3)
Close the cut in the door seal root as follows:
(a)
Push the seal to open the cut and very carefully prepare the surfaces of the cut with a very fine emery cloth.
(b)
Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the cut area and fill the stop holes.
1EFF : ALL 1 52-32-18Page 810 1 1 May 01/05 1 1 1CES 1
R R Reinforcement of Door Seal Figure 804/TASK 52-32-18-991-007
1EFF : 1 1 1CES ALL 1 111 52-32-18 Page 811 Aug 01/01
(c)
Press the surfaces of the cut together and leave them to dry for some minutes.
(d)
Cover the repair area with a layer of foil SPECIAL MATERIALS (Material No. 05-023) and put the seal in the wooden bonding block.
(e)
Compress the seal in the wooden bonding block with a clamp for a period of 24 hours.
(f)
Remove the wooden bonding block and the foil from the cut area of the seal.
(g)
Prepare the cut area with very fine emery cloth to get a smooth surface of the seal.
R **ON A/C 151-199, 401-499,
Subtask 52-32-18-350-051-A
A. Reinforcement of Door Seal
(Ref. Fig. 804/TASK 52-32-18-991-007)
(1)
Prepare the door seal as follows:
(a)
Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR57 and FR57A.
(b)
Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2)
Install the additional silicon tube into the door seal as follows:
(a)
Cut the additional silicon tube (Spec: NSA 3629-8-12) to a length of 3465.0 mm (136.4173 in.)
(b)
Push the seal to open the cut.
(c)
Carefully introduce the additional silicon tube into the door seal.
(3)
Close the cut in the door seal root as follows:
(a) Push the seal to open the cut and very carefully prepare the surfaces of the cut with a very fine emery cloth.
1EFF : ALL 1 52-32-18Page 812 1 1 Aug 01/05 1 1 1CES 1
(b)
Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the cut area and fill the stop holes.
(c)
Press the surfaces of the cut together and leave them to dry for some minutes.
(d)
Cover the repair area with a layer of foil SPECIAL MATERIALS (Material No. 05-023) and put the seal in the wooden bonding block.
(e)
Compress the seal in the wooden bonding block with a clamp for a period of 24 hours.
(f)
Remove the wooden bonding block and the foil from the cut area of the seal.
(g)
Prepare the cut area with very fine emery cloth to get a smooth surface of the seal.
**ON A/C ALL
5. Close-up
________ Subtask 52-32-18-410-052
A. Close Access
(1)
Install the reinforced door seal (Ref. TASK 52-31-18-400-001).
(2)
Close the AFT cargo compartment door (Ref. TASK 52-30-00-860-002).
1EFF : ALL 1 52-32-18Page 813 1 1 May 01/05R 1 1 1CES 1
LOCKING MECHANISM - DOOR - REMOVAL/INSTALLATION_______________________________________________
R **ON A/C 051-052,
R TASK 52-32-21-000-001
R Removal of the Locking Handle Mechanism
R 1. Reason for the Job__________________
R Self Explanatory
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(74)
