(7)
 Press and hold the ends of the replacement section and the seal
 together and let them dry for some minutes.

 (8)
 Cut a piece of SPECIAL MATERIALS (Material No. 05-024) to a size of the repair areas.

 (9)
 Apply a layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the contact surface of the replacement tissue and the repair areas.

 (10)
 Wind the replacement tissue around the repair areas.

 (11)
 Cover the repair area with a layer of foil SPECIAL MATERIALS (Material No. 05-023) and put the seal in the wooden bonding block.

 (12)
 Compress the seal over a period of 24 hours in the wooden bonding block with a clamp.

 (13)
 Remove the wooden bonding block and the foil from the repair area of the seal.

 (14)
 Prepare the repair area with very fine emery cloth to get a smooth surface on the seal.

 1EFF : ALL 1 52-32-18Page 807 1 1 Feb 01/98 1 1 1CES 1 Subtask 52-32-18-350-050

 C. Repair of the Chafe Marks
 (1)
 Prepare the chafe mark with very fine emery cloth.

 (2)
 Carefully degrease the chafe mark with CLEANING AGENTS (Material No. 11-016) and a lint-free cloth.

 (3)
 Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the chafe mark with a spatula.

 (4)
 Prevent a dust layer on the treated chafe marks during the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) drying period of 10 to 12 hours.

 5. Close-up
________ Subtask 52-32-18-410-051
 A. Close Access
 (1)
 Install the repaired door seal (Ref. TASK 52-32-18-400-001).

 (2)
 Close the applicable cargo compartment door (Ref. TASK 52-30-00-860-002).

 1EFF : ALL 1 52-32-18Page 808 1 1 Feb 01/98 1 1 1CES 1 1EFF : ALL 1 52-32-18Page 809 1 1 Aug 01/01 1 1 1CES 1

R  TASK 52-32-18-300-002 
R  Reinforcement of Door Seal 
R  1. Reason for the Job__________________ 
R  Self Explanatory 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific additional silicon tube (Spec: NSA 3629-8-12) 
R  No specific very fine emery cloth 
R  No specific wooden bonding block 
R  B. Consumable Materials 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  Material No. 05-023 USA MIL-I-631 
R  POLYTEREPTHALATE (Ref. 20-31-00) 
R  Material No. 08-004 USA MIL-A-25457 
R  ADHESIVE SEALANT (Ref. 20-31-00) 
R  Material No. 08-026 
R  ADHESIVE/SEALANT ONE PART,RTV SILICONE RUBBER 
R  (Ref. 20-31-00) 
R  C. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the 
R  Yellow Electric Pump 
R  52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the 
R  Yellow Electric Pump 
R  52-31-18-000-001 Removal of the Door Seal 
R  52-31-18-400-001 Installation of the Door Seal 
R  52-32-18-991-007 Fig. 804

 3. Job Set-up
__________
 Subtask 52-32-18-010-052

 A. Get Access
 (1)
 Open the AFT cargo compartment door and safty it with the support struts (Ref. TASK 52-30-00-860-001).

 (2)
 Remove the door seal (Ref. TASK 52-31-18-000-001).

 4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
 Subtask 52-32-18-350-051
 A. Reinforcement of Door Seal
 (Ref. Fig. 804/TASK 52-32-18-991-007)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門5(73)