(2)
Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to all the components of the vent door mechanism and to the adjacent cargo door structure.
(3)
Install the removed parts of the lining and insulation on the cargo door (Ref. TASK 52-32-13-400-001).
(4)
Install the vent door cover on the inner side of the cargo door.
(5) Install the access panel 826AR on the cargo door. R **ON A/C 151-199, 401-499,
Subtask 52-32-21-410-052-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to all the components of the vent door mechanism and to the adjacent cargo door structure.
R 1EFF : ALL 1 52-32-21Page 463 1 1 Aug 01/05 1 1 1CES 1
(3)
Install the removed parts of the lining and insulation on the cargo door (Ref. TASK 52-32-13-400-001).
(4)
Install the vent door cover on the inner side of the cargo door.
(5) Install the access panels 826AR, 826BR and 826CR on the cargo door. **ON A/C ALL
Subtask 52-32-21-865-058
B. Make sure that this(these) circuit breaker(s) is(are) closed: 1MJ, 3801GX, 3802GX, 3803GX.
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-32-21-410-053
C. Close Access
(1)
Remove the access platform(s).
(2)
Remove the actuator safety locks and close the AFT cargo door (Ref. TASK 52-30-00-860-002).
**ON A/C 051-052,
Subtask 52-32-21-410-053-A
C. Close Access
(1)
Remove the access platform(s).
(2)
Remove the actuator safety locks and close the AFT cargo door (Ref. TASK 52-30-00-860-002).
R 1EFF : ALL 1 52-32-21Page 464 1 1 Aug 01/05 1 1 1CES 1
TASK 52-32-21-000-004 Removal of the Safety Shaft Assembly
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-32-21-991-005 Fig. 406
3. Job Set-up
__________ Subtask 52-32-21-010-054
A. Get Access
(1)
Open the AFT cargo-compartment door (referred to as cargo door) and safety it with the actuator safety locks (Ref. TASK 52-30-00-860-001).
(2)
Put the access platform in position at the cargo door.
(3)
Remove the access panel 826AR from the cargo door.
(4)
Remove the plastic plug from the lateral cutout of the cargo door to remove the safety shaft.
1EFF : 051-052, 1 52-32-21Page 465 1 1 Aug 01/05R 1 1 1CES 1
Subtask 52-32-21-865-059
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/HYD POWER/Y 3803GX N30 122VU DOORS/CARGO 1MJ T12 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
4. Procedure
_________ Subtask 52-32-21-020-054
A. Removal of the Safety Shaft Assembly
(Ref. Fig. 406/TASK 52-32-21-991-005)
NOTE : Identify the installation position of the safety cams, the drift
____ pin levers, the link lever and the vent door lever with a mark.
(1)
Disconnect the connection rod (27) from the vent door lever (21) as follows:
(a)
Remove and discard the cotter pin (26) from the nut (25).
(b)
Remove the nut (25), the washers (23), the bush (24) and the bolt
(22) from the vent door lever (21). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(90)
