C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 064154 P. Block 1
NTM 57-20-47 PART 6
ASRM 572100 (for corrective action)
R 57-20-00-991-025 Fig. 624
3. Job Set-up
__________
Subtask 57-20-00-941-073
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3) Put the safety barriers in position.
Subtask 57-20-00-010-072
B. Get Access
(1)
Put the access platform in position below the applicable zone 470(480).
(2)
Remove the applicable access panels (Ref. AMM 064154 P. Block 1):
-
for the left wing, remove 471CL, 475BL, 472BR and 476BR
-
for the right wing, remove 481BL, 485BL, 482CR and 486BR.
4. Procedure
_________
R (Ref. Fig. 624/TASK 57-20-00-991-025) Subtask 57-20-00-110-074
A. Preparation for Inspection
(1)
Make sure that you remove all sealant from the surface around the aft pylon attachment-fitting cutout.
(2)
Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026), to clean:
-the surface around the aft pylon attachment-fitting cutout.
Subtask 57-20-00-280-056
B. Inspection
(1) Do a special detailed inspection of the bottom-skin, lower-surface around the aft pylon attachment-fitting cutout (Ref. NTM 57-20-47 PART 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
5. Close-up
________
Subtask 57-20-00-410-074
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels(Ref. AMM 064154 P. Block 1):
-
for the left wing, install 471CL, 475BL, 472BR and 476BR
-
for the right wing, install 482CR, 486BR, 481BL and 485BL.
R Details of the Aft-Pylon Attachment Fitting Cutout Figure 624/TASK 57-20-00-991-025
1EFF : 1 1 1CES ALL 1 111 57-20-00 Page A627 Aug 01/05
Subtask 57-20-00-942-074
B. Removal of Equipment
(1)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER flap/slat control lever locking tool from the flap/slat control lever.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-20-00Page A628 1 1 Aug 01/05R 1 1 1CES 1
TASK 57-20-00-200-025
Detailed Visual Inspection of the Outer Wing Bottom-Skin Root-Joint Fittings on Stringers 8 and 11
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572052-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notices
No specific access platform 2 m (6 ft. 7 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
98D57004013000 2 HOOK-COVER (RIB 2 SURGE DOORS)
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼1(100)
