C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-12-00-010-001 Open the Main Gear Doors for Access
32-12-00-410-001 Close the Main Gear Doors after Access
57-17-11-000-001 Removal of the Covers 147AZ (148AZ)
57-17-11-400-001 Installation of the Covers 147AZ (148AZ)
NTM 571109,P.Block-601
SRM 511100,P.Block 001 (for corrective action)
SRM 512200,P.Block 001 (for corrective action)
57-10-00-991-026 Fig. 602
3. Job Set-up
__________
Subtask 57-10-00-010-058
A. Get Access
(1)
Open the Main Landing Gear doors (Ref. TASK 32-12-00-010-001).
(2)
Install an access platform at the zone 147(148).
(3)
Remove the access covers 147AZ, 148AZ (Ref. TASK 57-17-11-000-001).
(4)
Take a torch for the inspection.
Subtask 57-10-00-110-065
B. Preparation of the Inspection Area
(Ref. Fig. 602/TASK 57-10-00-991-026)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-10-00Page 606 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Center Wing Box - Rear Spar - Inspection Area
Figure 602/TASK 57-10-00-991-026
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-10-00Page 607 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(1)
Clean the inspection surface with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003), if necessary.
(2)
Make sure that the surface of the inspection area is clean and smooth.
(3)
Do a check of the inspection area for visible damage or
discontinuities.
(4)
Make sure that there is no:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps, ...):
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
4. Procedure
_________
Subtask 57-10-00-250-050
A. Inspection
(Ref. Fig. 602/TASK 57-10-00-991-026)
(1)
Do a special detailed inspection of the center wing box rear spar around access door cutouts. Refer to the Non-destructive Testing Manual (Ref. NTM 571109,P.Block-601).
(2)
Make a report of damage after NDT inspection:
(a)
Corrosion damage:
-If you find damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps...):
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-10-00Page 608 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 57-10-00-410-058
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access covers 147AZ, 148AZ (Ref. TASK 57-17-11-400-001).
(3)
Remove the access platform.
(4)
Close the Main Landing Gear doors (Ref. TASK 32-12-00-410-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-10-00Page 609 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
TASK 57-10-00-200-006
Detailed Inspection of Center Wing Spanwise formed Angle along Lower Edge of Front Spar, Forward Face
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(42)
