R 1EFF : 001-049, 051-061, 101-105, 151-151, 1 57-20-00Page 606 1201-203, 1Aug 01/05 1 1 1CES 1
R **ON A/C 062-099, 106-149, 152-199, 204-299, 301-399, 401-499,
R Subtask 57-20-00-110-050-A
R A. Preparation for Inspection
R (1) Remove unwanted sealant from the access panel cut-out(s) and the seal
R faces of the access panels.
R (2) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with
R CLEANING AGENTS (Material No. 11-026), to clean:
R - the access panel assembly (1) interfaces
R - the bottom wing skin (3) interfaces and the adjacent area
R - the access panel outer (5) and the bolt (6) areas.
R Subtask 57-20-00-210-050-A
R B. Inspection
R (1) Examine the areas of the top and the bottom skin surfaces adjacent to
R the access panel cut-outs.
R Make sure that:
R - there is no corrosion of the access panel assembly (1) and the wing
R skin (3)
R - the sealing ring (2) is in good condition
R - the access hole edges in the wing skin (3) are not damaged
R - the knitted gasket (4) is in good condition
R - there is no damage to, or scoring of, the access panel outer (5)
R and the access panel assembly (1) interface
R - the bolt (6) holes in the access panel outer (5) are not damaged
R - the paint finish is of the correct condition.
R NOTE : If necessary, refer to the ASRM (Ref. ASRM 572000) for the____
R correct repair procedure.
R 1EFF : 062-099, 106-149, 152-199, 204-299, 1 57-20-00Page 607 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C ALL
R 5. Close-up________
R Subtask 57-20-00-410-050
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Install the applicable access panels (Ref. TASK 57-27-11-400-001):
R - for the left wing, install 540AB, 540BB
R - for the right wing, install 640AB, 640BB.
R Subtask 57-20-00-650-055
R B. Fuel Configuration
R (1) Refuel (Ref. TASK 12-11-28-650-003), defuel (Ref. TASK 28-25-00-650-
R 001) or transfer fuel (Ref. TASK 28-25-00-869-001) as necessary.
R Subtask 57-20-00-942-050
R C. Removal of Equipment
R (1) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat
R control lever.
R (2) Remove the safety barriers.
R (3) Remove the warning notice(s).
R (4) Remove the access platform(s).
R (5) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
TASK 57-20-00-200-032
Special Detailed Inspection of Outer Wing, Bottom Skin, Upper and Lower Surfaces, Around Access Door Cutouts in Rib Bay 2-3 and Rib Bay 6-7
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572040-03
2. Job Set-up Information
______________________
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼1(71)
