-
there are no cracks in the adjacent area
-
there is no corrosion
-the paint finish is in the correct condition. R NOTE : If necessary, refer to the (Ref. ASRM 572100) for the correct
____ R repair procedure.
5. Close-up
________
Subtask 57-21-00-410-073
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Install the overwing refuel adapter (Ref. TASK 28-11-43-400-001). Subtask 57-21-00-942-050
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-21-00-200-032
R Detailed Inspection of Outer Wing Top Skin, Upper Surface Around Manual R Refuelling Aperture between RIB19 and RIB20
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572122-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notices
No specific access platform 4.0 m (13 ft. 1 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 572100 57-21-00-991-001 (for corrective action)Fig. 602
3. Job Set-up__________
Subtask 57-21-00-941-085
A. Safety Precautions
R (1) Put the safety barriers in position.
R (2) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
R R (3) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-21-00-010-075
B. Get Access
(1) Put the access platform in position at the wing leading edge, zone 522 (622).
4. Procedure_________
(Ref. Fig. 602/TASK 57-21-00-991-001)
Subtask 57-21-00-110-081
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the top skin area around the manual refuel opening.
R 1EFF : ALL 1 57-21-00Page 606 1 1 Aug 01/04 1 1 1CES 1
R Manual Refuel Opening between RIB19 and RIB20 Figure 602/TASK 57-21-00-991-001
1EFF : 1 1 1CES ALL 1 111 57-21-00 Page 607 Aug 01/04
Subtask 57-21-00-210-084
R B. Inspection
R R R (1) Make a detailed inspection of the wing top skin surface adjacent to the manual refuel opening. Make sure that: - there is no damage to the adjacent area - there are no cracks in the adjacent area - there is no corrosion - the paint finish is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the____ correct repair procedure.
5. Close-up________
Subtask 57-21-00-942-083
A. Removal of Equipment
(1) Remove the safety barriers.
(2) Make sure that the work area is clean and clear of tool(s) and other items.
(3) Remove the warning notice(s).
(4) Remove the access platform(s).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(117)
