C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 572100 (for corrective action) R 57-20-00-991-024 Fig. 623
3. Job Set-up
__________
Subtask 57-20-00-941-072
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3)
Put the safety barriers in position.
(4)
Put the access platform in position below the applicable zones 571(671) and 574(674).
4. Procedure
_________ R (Ref. Fig. 623/TASK 57-20-00-991-024) Subtask 57-20-00-110-073
A. Preparation for Inspection WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
Details of the Bottom-Skin lower-Surface - Runouts at Stringers 2, 14 and 15 R Figure 623/TASK 57-20-00-991-024
1EFF : ALL 1 57-20-00Page A622 1 1 Aug 01/05 1 1 1CES 1
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004), to clean:
-the lower-surface of the bottom skin at the runouts of the stringers 2, 14 and 15.
Subtask 57-20-00-210-068
B. Detailed Visual Inspection of the Outer-Wing Bottom Skin Lower-Surface at the Runouts of Stringer 15 (rib-bay 2-3), Stringer 14 (rib-bay 3-4) and Stringer 2 (rib-bay 5-6)
(1) Examine the lower-surface of the bottom-skin at the runouts of the stringers 2, 14 and 15. Make sure that:
-
there is no corrosion or damage
-
there are no scratches, or scores
-
there are no loose or damaged fasteners
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-20-00-942-073
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-20-00Page A623 1 1 Aug 01/05R 1 1 1CES 1
TASK 57-20-00-200-024
Special Detailed Inspection of Outer Wing, Bottom Skin Lower Surface around Aft Pylon Attachment Fitting Cutout
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572047-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notices No specific access platform 2 m (6 ft. 7 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(99)
