C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
28-00-00-910-001 Fuel Safety Procedures 28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank 57-27-11-000-001 Removal of the Access Panel (540AB, 540BB, 540CB,
540DB, 540EB, 540FB, 540GB, 640AB, 640BB, 640CB, 640DB, 640EB, 640FB, 640GB)
57-27-11-400-001 Installation of the Access Panel (540AB, 540BB, 540CB, 540DB, 540EB, 540FB, 540GB, 640AB, 640BB, 640CB, 640DB, 640EB, 640FB, 640GB) ASRM 572100 (for corrective action)
R 57-20-00-991-017 Fig. 617
3. Job Set-up
__________
Subtask 57-20-00-941-065
A. Safety Precautions
WARNING : OBEY THE FUEL SAFETY PROCEDURES.
_______
(1)
Obey the fuel safety precautions (Ref. TASK 28-00-00-910-001) and (Ref. TASK 28-10-00-910-001).
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(4)
Put the safety barriers in position.
Subtask 57-20-00-010-065
B. Get Access
WARNING : OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
_______
(1)
Put the adjustable access platform in position below the zone 540(640)
(2)
Remove the applicable access panels:
-
for the left wing, remove 540BB and 540CB
-
for the right wing, remove 640BB and 640CB, (Ref. TASK 57-27-11-000-001).
4. Procedure
_________
R (Ref. Fig. 617/TASK 57-20-00-991-017)
Subtask 57-20-00-110-066
A. Preparation for Inspection
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004), to clean RIB7 and RIB8, and the pylon rear fitting. Do not clean the pick-up lug.
Subtask 57-20-00-210-063
B. Detailed Visual Inspection of the Outer Wing RIB7 and RIB8 and the Pylon Rear Fitting, Excluding the Pick-Up Lug
(1) Examine RIB7 and RIB8, and the pylon rear fitting. Make sure that:
-
there is no corrosion or damage
-
there are no scratches, or scores
-
there are no loose or damaged fasteners
-the surface protection is in the correct condition.
NOTE : Do not examine pick-up lug on the pylon rear fitting.
____
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
Details of the RIB7 and the RIB8 and the Pylon Rear Fitting R Figure 617/TASK 57-20-00-991-017
1EFF : ALL 1 57-20-00Page 694 1 1 Aug 01/05 1 1 1CES 1
5. Close-up
________
Subtask 57-20-00-410-066
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels:
-
for the left wing, install 540BB and 540CB
-
for the right wing, install 640BB and 640CB, (Ref. TASK 57-27-11-400-001).
Subtask 57-20-00-942-066
B. Removal of Equipment
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(92)
