(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the safety barriers.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-21-00Page 684 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-21-00-200-015
R R Detailed Inspection of Outer Wing, Bottom Skin Lower Surface at Attachments to Front Spar and Rear Spar, between RIB8 and RIB15, excluding areas.....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
1. Reason for the Job__________________
R R R Refer to the MPD TASK: 572129-01 Detailed inspection of outer wing, bottom skin lower surface at attachments to front spar and rear spar, between RIB8 and RIB15, excluding areas covered by pylon reinforcing, pylon fairing and flap track 3 fairing
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific 98D27803500001 safety barrierswarning noticesaccess platform 2 m (6 ft. 7 in.)2 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R Material No. 11-026 Material No. 19-003 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 572100 (for corrective action)
57-21-00-991-017 Fig. 615
3. Job Set-up
__________
Subtask 57-21-00-941-065
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3)
Put the safety barriers in position.
(4)
Put the access platform in position below the wing fuel tank, zone 540 (640).
4. Procedure
_________ (Ref. Fig. 615/TASK 57-21-00-991-017) Subtask 57-21-00-110-064 R A. Preparation for Inspection R
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with
R CLEANING AGENTS (Material No. 11-026) to clean the attachments to the front and the rear spars (RIB8 thru RIB15).
Details of the Bottom Skin Attachments - RIBS 8 thru 15 Figure 615/TASK 57-21-00-991-017
1EFF : ALL 1 57-21-00Page 687 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-21-00-210-069
B. Inspection
(1) Examine the lower surface of the bottom skin at the attachments to the front and the rear spars (RIB8 thru RIB15). Make sure that:
-
there is no corrosion or damage
-
there are no scratches or scores
-
there are no loose or damaged fasteners
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
5. Close-up
________ Subtask 57-21-00-942-064
A. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) from the flap/slat control lever.
(3)
Remove the safety barriers.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(137)
