-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
SRM 512200 PB 001 (for corrective action) SRM 512200,P.Block 001 (for corrective action) R 57-10-00-991-023 Fig. 616
3. Job Set-up
__________
Subtask 57-10-00-010-080
A. Get Access
(1)
Open the main landing-gear doors (Ref. TASK 32-12-00-010-001).
(2)
Put an access platform in position at the zone 147(148).
(3)
Remove the access covers 147AZ, 148AZ (Ref. TASK 57-17-11-000-001).
(4)
Use a FLASHLIGHT for the inspection.
Subtask 57-10-00-110-069
B. Preparation of the Inspection Area R (Ref. Fig. 616/TASK 57-10-00-991-023)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(1)
Remove the sealant from the fasteners (1) in the inspection area.
(2)
Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
First Row of Fasteners from RIB1 on the Upper Surface of the Triform Fitting R Figure 616/TASK 57-10-00-991-023
1EFF : ALL 1 57-10-00Page 675 1 1 May 01/05 1 1 1CES 1
(3)
Make sure that the surface of the inspection area is clean and smooth.
(4)
Do a visual check of the inspection area for damage or discontinuities.
(5)
Make sure that there is no:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200,P.Block 001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps, ...):
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100,P.Block 001) for damage classification and corrective action.
4. Procedure
_________
Subtask 57-10-00-270-050
A. Inspection R (Ref. Fig. 616/TASK 57-10-00-991-023)
(1)
Do a special detailed inspection of the first row of fasteners at RIB1 in the center wing box. This inspection is applicable to the upper surface of the triform fitting (2) (one each alternate bolt), between STIF8 and FR42 (Ref. NTM 571181 PB 401).
(2)
Make a report of the damage after the NDT inspection:
(a)
Corrosion damage:
-If you find damage, refer to the Structural Repair Manual (Ref. SRM 512200 PB 001) for types of corrosion, inspection, removal and corrosion protection. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(58)
