(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(4)
Put the safety barriers in position.
Subtask 57-20-00-010-064
B. Get Access
(1)
Put the adjustable access platform in position below the zone 540(640).
(2)
Remove the applicable access panels:
-
for the left wing, remove 540AB and 540BB
-
for the right wing, remove 640AB and 640BB (Ref. TASK 57-27-11-000-001).
4. Procedure
_________
R (Ref. Fig. 616/TASK 57-20-00-991-016)
Subtask 57-20-00-110-065
A. Preparation for Inspection
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004), to clean RIB5 and RIB6 around:
-
the skin attachments and the cleats
-
the spar attachment
-
the access cutouts
-
the stringer cutouts.
Subtask 57-20-00-210-062
B. Detailed Visual Inspection of the Outer Wing RIB5 and RIB6 at the Skin Attachments (including cleats), Spar-Attachment Access-Cutout Surrounds and in the Region of the Stringer Cutouts
(1) Examine RIB5 and RIB6. Make a check of the rib condition in these areas:
-
the skin attachments, and the cleats
-
the spar attachments
-
the access cutouts
-
the stringer cutouts
Make sure that:
-
there is no corrosion or damage
-
there are no scratches or scores
-
there are no loose or damaged fasteners
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
Details of the RIB5 and the RIB6 at the Skin Attachments R Figure 616/TASK 57-20-00-991-016
1EFF : ALL 1 57-20-00Page 689 1 1 Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 57-20-00-410-065
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels:
-
for the left wing, install 540AB and 540BB
-
for the right wing, install 640AB and 640BB, (Ref. TASK 57-27-11-400-001).
Subtask 57-20-00-942-065
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-20-00Page 690 1 1 Aug 01/05R 1 1 1CES 1
TASK 57-20-00-200-016
Detailed Visual Inspection of the Outer Wing RIB7 and RIB8 and the Pylon Rear Fitting excluding Pick-Up Lug
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572028-01
2. Job Set-up Information
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼1(91)
