曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

27-31-00-700-801 Null Procedure - Mach Trim Actuator (P/B 201)
27-31-00-800-801 Elevator Hydraulic System A and B - Pressurization (P/B 201)
27-31-00-800-802 Remove Pressure from the Elevator Hydraulic Systems A and B
(P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1672 Assembly - Lock, Stabilizer Trim
(Part #: F71336-501, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
SPL-1677 Assembly - Trammel Bar, Stabilizer Trim Actuator
(Part #: F80055-1, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
SPL-2030 Equipment - Pin Removal, Horizontal Stabilizer
(Part #: C55005-11, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
SPL-2035 Sling - Horizontal Stabilizer
(Part #: C55007-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
(Part #: C55007-29, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
317 Tail Cone Compartment - Left
318 Tail Cone Compartment - Right
330 Subzone - Left Horizontal Stabilizer and Elevator
340 Subzone - Right Horizontal Stabilizer and Elevator
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-11
Page 401
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
D. Access Panels
Number Name/Location
317AL Tail Cone Access Door
318BR Tailcone Access Door
331A Horizontal Stabilizer, Gap Cover
331AZ Horizontal Stabilizer, Access Panel, Inboard L.E. Closure Rib
332AB Horizontal Stabilizer, Gap Cover, Horizontal Stabilizer to Body
333AB Horizontal Stabilizer, Gap Cover, Horizontal Stabilizer to Body
333AZ Horizontal Stabilizer, Access Panel, Inboard T.E. Closure Rib
341A Horizontal Stabilizer, Gap Cover
341AZ Horizontal Stabilizer, Access Panel - Inbd L.E. Closure Rib
342AB Horizontal Stabilizer, Gap Cover - H. Stab. to Body
343AB Horizontal Stabilizer, Gap Cover - H. Stab. to Body
343AZ Horizontal Stabilizer, Access Panel - Inbd T.E. Closure Rib
E. Prepare for the Removal
NOTE: If the horizontal stabilizer is being removed and the same stabilizer, elevator, and elevator
tab is going to be re-installed (without elevator or elevator tab rework or adjustment), then
the following procedure will determine if a flight test is necessary.
NOTE: If the tailcone is removed or it’s position is adjusted during the elevator or stabilizer
removal procedure, the left and right elevator index plate positions will be in a different
position when the tailcone is re-installed. The elevator position cannot be properly
measured with the elevator index plate in a different location, therefore, you must do a
power-off flight test.
SUBTASK 27-41-11-700-001
(1) Do this task: Elevator Hydraulic System A and B - Pressurization, TASK 27-31-00-800-801.
SUBTASK 27-41-11-860-007
(2) Do this task: Null Procedure - Mach Trim Actuator, TASK 27-31-00-700-801.
SUBTASK 27-41-11-860-008
(3) Use the bar, SPL-1677 to set the B dimension of the horizontal stabilizer at 39.89 +/- 0.01 inches
(1013.2 +/- 0.3 mm) (this is a neutral stabilizer setting of zero degrees or 4 units of trim)
Figure 401.
SUBTASK 27-41-11-860-009
(4) Move the control column forward and aft several times and then let it go at the neutral position.
SUBTASK 27-41-11-860-010
(5) Do the following to measure the elevator position:
(a) Measure the left elevator position on the elevator index plate Figure 403.
NOTE: Be sure to note if the elevator is above or below the neutral mark.
(b) Measure the right elevator position on the elevator index plate Figure 403.
NOTE: Be sure to note if the elevator is above or below the neutral mark.
SUBTASK 27-41-11-860-001
(6) Do this task: Remove Pressure from the Elevator Hydraulic Systems A and B,
TASK 27-31-00-800-802.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-11
Page 402
Jun 10/2006
D633A101-GUN
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3(124)