F. Prepare for the Test
SUBTASK 27-31-00-860-083
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS,
ELEVATORS, FLAPS, SPOILERS, SLATS, AND THRUST REVERSERS CAN MOVE
QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) Pressurize elevator hydraulic systems A and B. To pressurize them, do this task: Elevator
Hydraulic System A and B - Pressurization, TASK 27-31-00-800-801.
SUBTASK 27-31-00-860-084
(2) Do this task: Null Procedure - Mach Trim Actuator, TASK 27-31-00-700-801.
SUBTASK 27-31-00-010-017
(3) Open this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
SUBTASK 27-31-00-860-085
(4) Use the bar, SPL-1677 to set the "B" dimension at 21.32 +/- 0.10 inches (541.5 +/- 2.5 mm)
(Figure 502).
G. Neutral Shift Test
SUBTASK 27-31-00-730-010
(1) Do the neutral shift test:
(a) Make sure the right elevator trailing edge moves up 13.90 - 14.90 inches (353.1 - 378.5 mm)
from the index mark (Figure 523).
(b) Use the bar, SPL-1677 to set the "B" dimension at 45.84 +/- 0.10 inches (1164.3 +/- 2.5
mm).
(c) Move the captain’s control column aft and forward lightly to make sure it is in the neutral
position.
(d) Make sure the right elevator trailing edge moves down 3.20 - 3.80 inches (81.3 - 96.5 mm)
from the index mark.
SUBTASK 27-31-00-700-006
(2) Do the following steps to check the elevator system:
NOTE: You use the Flight Management Computer Control Display Unit (FMC CDU) to do the
following Built-In-Test Equipment (BITE) test.
(a) If you need to supply electrical power, do this task: Supply Electrical Power,
TASK 24-22-00-860-811
(b) Push the INIT REF key on the CDU keyboard.
1) Push the Line Select Key (LSK) that is adjacent to each selection:
a) INDEX
b) MAINT
c) DFCS
d) EXTENDED MAINTENANCE
e) RIGGING
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-00
Page 585
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
f) ELEVATOR
NOTE: After you make this selection, the CONTINUE will show. Do the instructions
that show on the CDU display before you push the LSK that is adjacent to
CONTINUE.
g) COMPLETE ELEV RIG
NOTE: This selection contains the ELEV RIG test.
h) During this test, do the instructions that show on the CDU display.
i) After you do the instructions that show on the CDU display, push the LSK that is
adjacent to CONTINUE.
2) Do the Elevator Rigging Check:
a) Make sure that the values for the A and B sides are between the limits that show on
the CDU display or in this task.
Table 504/27-31-00-993-820
Test Limits:
51.01 STAB POS (VAC) -0.07 to 0.07
b) Use the trammel bar, SPL-1677 to measure the B dimension.
c) Make sure that the B dimension is 39.89 (±0.01) inches.
Table 505/27-31-00-993-821
Test Limits
51.02 MT ACT POS (VAC) -8.70 to -6.35
Note: No value for B side; N/A
51.03 MT ACT POS (VAC) -0.20 TO 0.20
Note: No value for B side; N/A
51.04 ELEV POS (vac) -0.55 RO -0.45
d) Make sure that the elevator trailing edge aligns with the elevator index on the tail
cone at 0 (±0.06) inch.
Table 506/27-31-00-993-822
Test Limits
51.05 NSS POS (VAC) -1.77 to -1.67
51.06 ELEV LVDT (VAC) -2.05 to -1.95
51.07 ELEV POS (VAC) -0.55 TO -0.45
e) Make sure that the elevator trailing edge aligns with the elevator index on the tail
cone at 0 (±0.06) inch.
Table 507/27-31-00-993-823
Test Limits
51.08 ELEV POS (VAC) -0.55 to -0.45
51.09 ELEV POS (VAC) -0.55 to -0.45
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-00
Page 586
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
51.10 ELEV POS (VAC) -0.55 to -0.45
51.11 ELEV POS (VAC) -0.55 to -0.45
f) Set the B dimension to 29.00 (±0.01) inches.
g) Use the trammel bar, SPL-1677 to measure the B dimension.
h) Make sure that the B dimension is at 29.00 (±0.01) inches.
Table 508/27-31-00-993-824
Test Limits
51.12 STAB POS (VAC) 4.47 to 5.29
51.13 ELEV LVDT (VAC) -0.06 to 0.06
51.14 ELEV POS (VAC) -0.10 to 0.10
51.15 NSS POS (VAC) -0.20 to 0.20
3) Do these steps to get out of the BITE test:
NOTE: If there are instructions on the CDU display, it is necessary to do the
instructions that show on the CDU display.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊3