27-51-40
 ALL  ú ú 01 Page 424 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | | 96 |Washer (Track No. 1 and 8) | | 01 | 415 | | | |Washer (Track No. 2 and 7) | | 03 | 345 | | | 97 |Nut (Track No. 1 and 8) | | 01 | 420 | | | |Nut (Track No. 2 and 7) | | 03 | 350 | | | 98 |Spring Support (Track No. 1) | | 01 | 485 | | | |Spring Support (Track No. 2) | | 03 | 420 | | | |Spring Support (Track No. 7) | | | 425 | | | |Spring Support (Track No. 8) | | 01 | 490 | 2......…........…...................................…..........….....….........1
 C. References
 (1)  
AMM 27-51-04/401, Outboard Flap

 (2)  
AMM 27-51-40/601, Outboard Aftflap Drive Mechanism

 D.
Access

 (1)  
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)

 667  Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
 E. Procedure
 S 224-048
 (1)  
If you will install used parts, do this task: "Outboard Aftflap Drive Mechanism Inspection" (AMM 27-51-40/601).

 S 424-049

 (2)  
Install the geneva cam (Fig. 401).

 (a)  
Apply a thin layer of grease to the bolt (52) and the bushing (53) (Section F-F).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-40
 ALL  ú ú 01 Page 425 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  
Put the bushing (53) in the support fitting.

 (c)  
Put the geneva cam in its position on the carriage.

 (d)  
Install the bolt (52), washer (51), bushing (53), and lube fitting.

 (e)  
Install the shim washers (51 and 57) if it is necessary to get the clearances shown in Section E-E.

 (f)  
Install the washer (55) and the nut (54) on the bolt.

 (g)  
Tighten the nut to 270-300 pound-inches (31-34 N-m). Continue to tighten the nut to align the subsequent cotter pin hole.

 (h)  
Install the cotter pin.

 CAUTION: MAKE SURE THAT THE ENDS OF THE SPRING ARE FREE TO TURN.
_______ THE SPRINGS CAN BE DAMAGED IF THE ENDS CANNOT TURN.
 (i)  If it is necessary, install the springs on the geneva cam (Detail F): 1) Install the bushing (94) in the springs (37) and install
 the flanged bushings (90) in the bushings (94). 2) Install the bolt (91) through the flanged bushings and the
 spring support (98). 3) Install the washer (96) and the nut (97) on the bolt (91). 4) Install the screw (93) through the bushing (92), flanged
 bushings (90) and spacer (95). 5) Install the washer (96) and the nut (97) on the screw (93). 6) Tighten the nuts to 50-80 pound-inches (5.6-9.0 N-m). 7) Install the cotter pins.
 (j)  Connect the pushrod (Section H-H): 1) Install the bushing (72) in the geneva cam. 2) Put the pushrod (1) in its position in the geneva cam. 3) Install the washer (69) between the rod end and the bushing
 (72). 4) Attach the rod end with the bolt (67), washer (68 and 70), and nut (71). 5) Tighten the nut to 120 pound-inches (14 N-m). Continue to tighten the nut to align the subsequent cotter pin hole. 6) Install the cotter pin.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-40
 ALL  ú ú 03 Page 426 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(112)