(3)  
SOPM 20-10-03, Shot Peening

 (4)  
SOPM 20-42-10, Low Hydrogen Embrittlement Cadmium Plating

 C.  
Access

 (1)  
Location Zone
 587 Outboard Flap Midflap, LH
 687 Outboard Flap Midflap, RH

 D.  
Procedure

 S 018-002
 (1)  
Remove the foreflap carriage stop (AMM 27-51-27/401).

 S 328-014

 (2)  
Remove the corrosion from the flap track surface.

 (a)  
Machine or hand clean corrosion from the top surface of the flap track.

 NOTE: Do not remove more than 0.020 inch (0.51 mm) of
____ material from the flap track. Keep a 63 microinch
 (1.6 micron) finish (SOPM 20-10-02).
 (b)  
Shot-peen the repaired surface (SOPM 20-10-03).

 (c)  
Apply low hydrogen embrittlement cadmium plating to the repaired surface (SOPM 20-42-10).

 S 328-015
 (3)  
Remove the corrosion from the holes for the stop mount (if it is necessary).

 (a)  
Ream the holes to 1/16-inch (1.59 mm) oversize to remove corrosion and to prepare to install the bushing.

 (b)  
Apply low hydrogen embrittlement cadmium plating to the holes (SOPM 20-42-10).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-27
 ALL  ú ú 01 Page 801 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  Prepare bushings from 17-4 PH CRES.
 NOTE: The inner diameter must match the bolts with a
____ 0.0003-0.0014 inch (0.008-0.036 mm) interference fit.
 (d)  
Apply low hydrogen embrittlement cadmium plating to the bushings (SOPM 20-42-10).

 (e)  
Install the bushings in the holes.

 E.
Finish The Repaired Areas

 S 378-011
 (1)  
Apply one layer of the epoxy primer to the repaired area.

 S 378-012

 (2)  
Let the primer dry.

 S 378-016

 (3)  
Apply one layer of the polyurethane enamel.

 S 378-013

 (4)  
Let the polyurethane enamel dry.

 (5)  
Install the foreflap carriage stop (AMM 27-51-27/401).

 S 438-017
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-27
 ALL  ú ú 01 Page 802 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 OUTBOARD FLAP CARRIAGE - REMOVAL/INSTALLATION
_____________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is one task for the removal and one task for the installation of an outboard flap carriage. The procedure has these parts:
 (1)
The removal of the outboard flaps

 (2)
The removal of the carriage

 (3)
A check of the carriage for worn areas

 (4)
The installation of the carriage

 (5)
The installation of the outboard flaps.

 TASK 27-51-28-004-001
 2.  Outboard Flap Carriage Removal______________________________
 A.  Special Tools and Equipment
 (1)
5ME65B01900 Main Carriage Retainer Nut Wrench

 (2)
10ME65B01900 Outboard Flaps Bearing Removal Tool

 (3)
5OHME65B0200 TE Flap Main Carriage Sling

 B.  
References

 (1)
27-51-04/401, Outboard Flap

 (2)
27-51-31/401, Outboard Flap Track Fairings

 (3)
IPC 27-51-04, Fig. 1 (Retainer Nut Area)

 (4)
IPC 27-51-28, Fig. 1 (Aft Thrust Collar Area)

 C.  
Access

 (1)  
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)

 667  Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(40)