曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

1  BUSHING  ID  0.5000  0.5010  0.5045  0.005  X 
BOLT  OD  0.4990  0.4995  0.4950  X 
2  BUSHING  ID  0.6860  0.6875  0.6905  0.005  1 
BUSHING  OD  0.6845  0.6855  0.6810  X 
3  BEARING  ID  0.4995  0.5000  0.5045  0.005  X 
BOLT  OD  0.4990  0.4995  0.4945  X 
4  BUSHING  ID  0.5000  0.5010  0.5045  0.005  1 
BOLT  OD  0.4990  0.4995  0.4950  X 
5  BUSHING  ID  0.5000  0.5010  0.5045  0.005  1 
BOLT  OD  0.4990  0.4995  0.4950  X 
6  BUSHING  ID  0.6860  0.6875  0.6905  0.005  1 
BUSHING  OD  0.6845  0.6855  0.6810  X 
7  BEARING  ID  0.4995  0.5015  0.5045  0.005  X 
BOLT  OD  0.4990  0.4995  0.4925  X 
8  BUSHING  ID  0.5000  0.5010  0.5045  0.005  1 
BOLT  OD  0.4990  0.4995  0.4920  X 
9  BUSHING  ID  0.4375  0.4385  0.4420  0.005  1 
BOLT  OD  0.4365  0.4370  0.4325  X 

Inboard Flap Fairing Fixed Drive Link Wear Limits
Figure 602 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-26
 ALL  ú ú 01 Page 608 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

INDEX NO.  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE PART WORN  REPAIR WORN PART  REPAIR INSTR. 
DIAMETER  PERM-WEAR DIM. ITTED  DIAM CLEAR-ANCE MAX 
MIN  MAX 
10  BUSHING  ID  0.6235  0.6250  0.6280  0.005  1 
BUSHING  OD  0.6220  0.6230  0.6185  X 
11  BEARING  ID  0.4370  0.4375  0.4420  0.005  X 
BOLT  OD  0.4365  0.4370  0.4320  X 
12  BUSHING  ID  0.4375  0.4385  0.4420  0.005  1 
BOLT  OD  0.4365  0.4370  0.4325  X 
13  BUSHING  ID  1.3754  1.3762  1.3800  0.006  X 
PIVOT PIN  OD  1.3730  1.3740  1.3694  X 
14  BUSHING  ID  1.3745  1.3755  1.3800  0.006  X 
PIVOT PIN  OD  1.3730  1.3740  1.3694  X 

A REPLACEMENT BUSHING CAN HAVE AN OVERSIZE OD TO 0.03 INCH. REAM THE ID TO THE DESIGN LIMITS. THE REPLACEMENT BUSHING MUST HAVE THE SAME INTERFERENCE FIT AS THE ORIGINAL BUSHING.
Inboard Flap Fairing Fixed Drive Link Wear Limits
Figure 602 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-26
 ALL  ú ú 01 Page 609 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 OUTBOARD FLAP TRACK - REMOVAL/INSTALLATION
__________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is one task for the removal and one task for the installation of the outboard flap track.
 (1)  
The removal procedure has these parts:

 (a)  
The removal of the outboard flap and carriage forward bogie

 (b)  
The removal of the foreflap sequence carriage

 (c)  
The removal of the flap transmission and ball screw

 (d)  
The removal of the flap track.

 (2)  
The installation procedure has these parts:

 (a)  
A check of the parts which attach the flap track for worn areas

 (b)  
The installation of the flap track

 (c)  
The lubrication of the flap track fittings

 (d)  
The installation of the flap transmission and ball screw
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(33)