washer (36) and nut (35).

 (c)  
On fairings No. 2 and 7, If you will disconnect the movable fairing at the flap track and fixed drive link, do the following (Fig. 403, View C): 1) Put padding inside the movable fairing to protect the

 linkage assembly and fairing skin from scratches and abrasions. 2) Remove the bolt that attaches the drive rod to the midflap fitting. 3) Disconnect the fixed drive link from the flap track (View E-E). 4) Remove the bolt (69), nut (70), and washers (71) that hold the link pivot pin in place.
 CAUTION: WHEN YOU REMOVE THE LINK PIVOT PIN, THE FLAP DRIVE
_______ LINK WILL SEPARATE FROM THE FLAP TRACK. BE PREPARED TO LOWER THE LINKAGE ASSEMBLY ONTO THE PADDING IN THE MOVABLE FAIRING. IF YOU DO NOT SUPPORT THE LINKAGE ASSEMBLY, DAMAGE TO HARDWARE COULD OCCUR.
 5) Remove the link pivot pin (68) from the joint.
 (d)  If you will disconnect the movable fairing at the fairing fitting and the support fitting, remove the support fitting from the fairing fitting: 1) Hold the fairing in its position.
 NOTE: The fairing weighs approximately 80 pounds (36 kg).
____
 2)  On fairings No. 1 and 8, remove the two bolts (25 and 30), washers (26 and 29), bushings (24, 27, 28 and 31), washers (23 and 32) and nuts (22 and 33).
 3)  On fairings No. 2 and 7, remove the two bolts (25 and 30), washers (26 and 29), bushings (24, 27 and 28), washers (23 and 32) and nuts (22 and 33).
 (e)  Remove the two bolts (48 and 49), washers (47 and 50), bushings (46 and 51), washers (44 and 52), and nuts (45 and 53) which attach the movable fairing to the hinge (Section A-A, Fig. 403).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 01 Page 407 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SNUBBER BLOCK
SEE  E 
SEE  B  SEE  C 
SEE  A 
A 
1. TIEBOLT 
16. ADJUSTABLE ROD (2 LOCATIONS)  D  2. TIEBOLT LOCK  D  5. NUT 4. WASHER 3. BOLT  A  TRANSMISSION 6. BRACE 
FAIRING FIXED  15. HINGE FITTING  A  9. NUT 8. WASHER 7. BOLT 10. BONDING JUMPER 
14. MOVABLE FAIRING ACCESS PLATE  13. NUT 12. WASHER 11. SCREW 
B 

Outboard Movable Flap Track Fairing Installation Figure 403 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 01 Page 408 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

C C
UPPER DOOR
ACCESS
DRIVE ROD  LINK
PLATE AFT DOOR
FIXED LINK  SEE D LINK
SUPPORT DOOR FITTING FITTING
FWD SUPPORT FITTING
E C
FLAP
B
TRACK
E C
B
FAIRINGS NO. 2 AND 7 FAIRINGS NO. 1 AND 8 LINKAGE SHOWN IN RETRACTED POSITION
LINKAGE SHOWN IN RETRACTED POSITION
C C
UPPER DOOR LINK
AFT DOOR
LINK

39. WASHER DOOR FITTING
38. BOLT
FAIRING FITTING37. BUSHING 17. BOLT36. WASHER SUPPORT
35. NUT FITTING
34. FORWARD
DOOR LINK

18.
 ANTI-ROTATION PLATE

19.
 WASHER

20.
 WASHER

33. NUT
21. NUT
32. WASHER 24. BUSHING 22. NUT
31. BUSHING
30. BOLT 23. WASHER
29. WASHER
25. BOLT
27.
 BUSHING

28.
 BUSHING

FAIRING FITTTING 26. WASHER
FAIRING NO. 1 AND 8
D
Outboard Movable Flap Track Fairing Installation Figure 403 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 02 Page 409 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
15. HINGE BALL SCREW
FITTING56. WASHER FLAP 40. BUSHING
TRANSMISSION (FAIRING
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(50)