PART NUMBER TRANS POSITION MISSION  MOUNTING LUG  |0.005 (|0.13) THICKNESS INCH (mm) SPACER  PART NUMBER 
65B81126-()  1 AND 8  A C B  0.200 (5.08) 0.200 (5.08) 0.160 (4.06)  69B83123-6 69B83123-1 69B83123-4 
65B81127-()  2 AND 7  C B A  0.180 (4.57) 0.180 (4.57) 0.140 (3.56)  69B83123-8 69B83123-7 69B83123-7 
65B81128-()  3 AND 6  C B A  0.031 (0.79) 0.031 (0.79) NONE  69B83123-2 69B83123-2 
65B81129-()  4 AND 5  C B A  0.040 (1.02) 0.040 (1.02) NONE  69B83123-5 69B83123-9 

Transmission Installation
Figure 402 (Sheet 5)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 01 Page 410 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-009
 (2)  
Disconnect the torque tubes from the transmission.

 (a)  
Remove the screws which attach the spline coupling sleeve to the torque tube.

 (b)  
Remove the torque tubes from the transmission.

 S 034-051
 (3)  
Disconnect the ball screws from the transmission.

 (a)  
Make a mark of the position of the ball screw and the universal joint.

 NOTE: The marks will help to make sure that you can install
____ the ball screw and the transmission correctly.
 (b)  Remove the two bolts (5), washers (3 and 4) and the nuts (2) which attach the ball screw to the universal joint.
 CAUTION: MAKE SURE THAT THE ANGLE BETWEEN THE TRANSMISSION AND THE
_______ BALL SCREW CENTERLINES IS NOT MORE THAN 10 DEGREES. YOU CAN CAUSE DAMAGE TO THE UNIVERSAL JOINT.
 (c)  
Install the ball and screw support tool (Fig. 403).

 (d)  
If you will not replace the ball screw, turn the ball screw out of the universal joint.

 S 034-013
 (4)  
Remove the ball screw if it is necessary (AMM 27-51-41/401).

 (a)  
Install the support equipment (Fig. 403). 1) If an outboard flap transmission will be removed, install

 the hoisting point clamp on the flap track. 2) Attach the lifting strap to the transmission. 3) Attach a fishpole hoist.
 NOTE: On the inboard flaps, attach the hoist to the
____ structural attachment point above the flap track. On the outboard flaps, attach the hoist to the hoisting point clamp.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 01 Page 411 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE  A 
TRANSMISSION  SEE  B  SCREW BALL  SUPPORT TOOL BALL AND SCREW 

FISHPOLE HOIST 
HOISTING POINT CLAMP 
(OUTBOARD FLAPS ONLY; 
THE INBOARD FLAPS USE A 
LIFTING POINT ATTACHED 
PERMANENTLY TO THE 
STRUCTURE)  A 
TRANSMISSION 
____NOTE:  TOOLS CAN BE USED ONLY IF THE 
FLAP FAIRING IS REMOVED. 
FLAP TRACK 

LIFTING STRAP
B
Transmission Installation Tools Figure 403
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 03 Page 412 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 4) Attach the fishpole hoist to the lifting strap.
 S 024-015
 (5)  Remove the transmission (Fig. 402)
 CAUTION:_______BE CAREFUL WITH THE FLAP TRACK FAIRINGS. YOU CAN EASILY CAUSE DAMAGE TO THE FAIRING SKIN.
 (a)  
If you will remove an outboard flap transmission (1), make sure the forward end of the fairing does not move.

 (b)  
Remove the bolts (10, 16, and 19), washers (11, 15, and 20), washers (7, 13, and 22), and nuts (8, 12, and 21) which attach the transmission to the flap track.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(70)