747-400
MAINTENANCE MANUAL

SEE A
UPSTOP 
TRANSMISSION 
SEE UNIVERSAL JOINT  B  BALL SCREW NUT  DOWNSTOP BALL SCREW 
(1143 |6.35 mm) 45.00 |0.25 INCH (DIMENSION X)  A 

STOP
UNIVERSAL BALL JOINT SCREW NUT
B

Flap Transmission Clearance
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-40
 ALL  ú ú 01 Page 439 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 CAUTION:_______ ADJUST THE AFTFLAP ACTUATOR RODS (AFT RODS) ONLY.  THE
 AFTFLAP MUST BE IN THE TOLERANCE SHOWN IN SECTION B-B ON
 THE TWO ENDS OF THE AFTFLAP TO PREVENT DAMAGE TO THE
 FLAPS.
 THE PUSHRODS (1) (FORWARD RODS) MUST BE KEPT AT THE
 CORRECT LENGTH (36.89 INCHES) (937 mm) TO PREVENT ROD
 LOADS THAT ARE TOO HIGH.  THE PUSHRODS CAN BE DIFFERENT
 FROM THE SPECIFIED LENGTH ONLY WHEN THE ACTUATOR RODS
 CANNOT BE ADJUSTED TO GET THE SPECIFIED LENGTH.  IF YOU
 MUST ADJUST THE PUSHRODS, THEY MUST BE THE SAME LENGTH.

 (b)  
Adjust the rod ends: 1) Tighten the checknuts on the rods. 2) Install the lockwire on the checknuts. 3) Make sure you can see the rod end threads through the

 inspection hole.

 (c)  
Put the bushing (33) in the aftflap fitting.

 (d)  
Attach the actuator rod the the aftflap fitting with a bolt (29), washers (28 and 31), and nut (32).

 (e)  
Tighten the nut to 270-300 pound-inches (31-34 N-m). Continue to tighten the nut to align the subsequent cotter pin hole.

 (f)  
Install the cotter pin.

 S 824-084
 (5)  
Adjust the bulb seal on the midflap trailing edge until the seal is compressed as shown in Section B-B, Fig. 401.

 S 864-085

 (6)  
Put the flap control lever in the position of the flaps.

 S 864-086

 (7)  
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P415 Power Distribution Panel 1) 415M24 ALT OUTBD TE FLAPS

 S 864-087
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU DISARM ALTERNATE CONTROL. THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
 (8)  
Push the ALTN FLAPS ARM switch to disarm the flaps alternate control.

 S 864-088

 (9)  
Do this task to pressurize hydraulic system No. 4: "Hydraulic System Pressurization" (AMM 29-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-40
 ALL  ú ú 02 Page 440 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 714-089
 CAUTION:_______MONITOR THE FLAP MOVEMENT CAREFULLY. THE FLAPS CAN BE DAMAGED BY INCORRECTLY ADJUSTED COMPONENTS.
 (10)
 Extend and retract the flaps.

 (a)  
Make sure the flaps move smoothly.

 S 864-103
 (11)
 Put the flap control lever in the 30-unit detent to extend the flaps and attach a DO-NOT-MOVE tag.

 S 644-090

 (12)
 Do this task to lubricate the aftflap drive mechanism:  "Trailing Edge Flap System Lubrication" (AMM 12-21-20/301).

 E.
Put the Airplane Back to Its Usual Condition

 S 864-105
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
 (1)  
Remove the DO-NOT-MOVE tag and put the flap control lever in the UP detent to retract the flaps.

 S 864-092

 (2)  
Do this task to depressurize hydraulic system No.4: "Hydraulic System Depressurization" (AMM 29-11-00/201).

 (3)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(119)