STOP 8. WASHER 43. HINGE
9. NUT LINK
44. WASHER
6. BRACE
0.045 |0.035
INCH
49. BOLT
53. NUT 45. NUT 48. BOLT
50. WASHER
64.
NUT 52. WASHER
65.
BOLT
FAIRING(2 LOCATIONS)
(2 LOCATIONS) FAIRING 47. WASHER
FITTING66. WASHER FITTING
51. BUSHING
(2 LOCATIONS) 46. BUSHING
A-A
SPRING MOUNTED SNUBBER BLOCK
E
25.
BOLT
26.
WASHER
PLATE
18. ANTIROTATION
31. BUSHING
28. BUSHING SUPPORT
FITTING29. WASHER
24. BUSHING
30. BOLT
23. WASHER
22. NUT
17. BOLT
21. NUT
57. WASHER 33. NUT
20. WASHER 58. WASHER 57. WASHER
32. WASHER
FAIRING FITTING
58. WASHER 17.36 INCHES ADJUSTABLE
(NOMINAL) ROD
FAIRING NO. 2 AND 7
B-B
DOOR FITTING (FAIRINGS
61. WASHER NO. 1 AND 8)
16. ADJUSTABLE ROD 1. TIE
59.
WASHER
BOLT
60.
NUT
C-C
2. TIE 16. ADJUSTABLE
BOLT ROD
LOCK
D-D
Outboard Movable Flap Track Fairing Installation Figure 403 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-31
ALL ú ú 01 Page 410 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
71. WASHER
70. NUT
68. LINK PIVOT PIN
FAIRINGS NO. 2 AND 7
E-E
Outboard Movable Flap Track Fairing Installation
Figure 403 (Sheet 4)
H69820
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-31
ALL ú ú 01 Page 411 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
CAUTION:_______BE CAREFUL WITH THE FAIRING DURING THE REMOVAL. YOU CAN EASILY CAUSE DAMAGE TO THE FAIRING SKIN.
(f) Lower the movable fairing from the airplane.
NOTE: Use the guide ropes to make sure the fairing does not
____
turn in the dolly.
S 034-009
(4)
Remove the hinge, if a replacement is necessary (Fig. 403):
(a)
Remove the tiebolt (1), tiebolt lock (2), bolt (3), washer (4), nut (5) washers (59 and 61), nut (60) and two adjustable rods (16) (Section D-D).
(b)
Remove the hinge link and brace with the hinge fitting: 1) Remove the hinge bolt (54), washer (55), washer (41), and
nut (42). 2) Remove the bushing (40) from the hinge fitting.
(c)
Disassemble the hinge fitting and brace: 1) On fairings No. 1 and 8, remove the bolt (7), washers (8) and nut (9).
2) On fairings No. 2 and 7, remove the bolt (7), washers (8 and 56) and nut (9).
TASK 27-51-31-404-010
3. Outboard Flap Track Fairing Installation
________________________________________
A. Special Tools and Equipment
(1)
PF51-009-1 Fishpole Hoists (2 necessary).
(2)
PME65B00110-53 Flap Track Fairing Handling Dolly
(3)
OHME65B00110-53 Flap Track Fairing Bootstrap Clamp
(4)
G27017 Fairing No. 1 and 8 Door Rigging Bar
B.
Consumable Materials
(1)
D00633 Grease - BMS 3-33 (recommended)
(2)
D00013 Grease - MIL-G-23827 (alternative)
C. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Bolt | 27-51-31 | 01 | 115 | | | 2 | Retainer - Bolt | | | 110 | | | 3 | Bolt - Tie (Outboard Side, | | | 120 | | | | Fairings No. 1 and 8) | | | | | | | Bolt - Tie (Inboard Side, | | | 125 | | | | Fairings No. 1 and 8) | | | | | | | Bolt - Tie (Outboard Side, | | | 130 | | | | Fairings No. 2 and 7) | | | | | | | Bolt - Tie (Inboard Side, | | | 135 | | | | Fairings (No. 2 and 7) | | | |
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(51)
