(b)  
Remove the lockbolt (1), the nut (2) and the washer.

 (c)  
Remove the lockbolt (8), the nut (9) and the washer from the bolt (11).

 (d)  
Hold the lower side brace (3) and pull out the lower bolt (11) and the support bracket (10) of the cable pulley.

 (e)  
Hold the upper side brace (3) and pull out the upper bolt (5).

 NOTE: The removal of the upper side brace is the same as the
____
 lower side brace.

 (f)  Remove the fasteners which holds the stirrup (13) to support bracket (14) and remove the bracket. 1) If it is necessary, remove the washer (15) from the right
 side.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-06
 ALL  ú ú 01 Page 403 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g) Remove the side braces from the nose landing gear.
 TASK 32-21-06-404-007
 3.  Nose Landing Gear Side Brace Assembly Installation (Fig. 401)__________________________________________________
 A. Consumable Materials
 (1)  
D00633 Grease - BMS 3-33 (preferred)

 (2)  
D00013 Grease - MIL-G-23827 (optional)

 (3)  
B00722 Solvent - PD-680 or equivalent cleaning solvent

 (4)  
A00226 Compound - Sealing, BMS 8-45 (Putty - Tamperproof)

 B.
References

 (1)  
AMM 07-11-02/201, Jacking Airplane Nose

 (2)  
AMM 12-15-05/301, Nose Gear Shock Strut Servicing

 (3)  
AMM 32-21-06/601, Nose Gear Side Brace

 (4)  
AIPC 32-21-06 Fig. 1

 (5)  
AIPC 32-61-58 Fig. 1

 C.
Access

 (1)  
Location Zone
 715 Nose Landing Gear

 D.
Prepare for the Procedure

 S 114-008
 (1)  
Clean side brace bolts, washers and nuts with naphtha.

 S 224-009

 (2)  
Examine the bolts and the bushings for wear limits
 (AMM 32-21-06/601).

 S 434-010

 (3)  
Assemble the lube inserts.

 (a)  
Examine the O-rings on the lube inserts for worn areas or damage and replace if it is necessary.

 (b)  
Apply a large quantity layer of grease to the O-rings, the lube inserts, and the internal surface of the bolts.

 (c)  
Move the O-rings to the retainers and lubricate the surfaces to put into if it is necessary.

 (d)  
Install the lube inserts into the bolts to form the pin assembly, and align the lockbolt holes.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-06
 ALL  ú ú 01 Page 404 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E.  Procedure
 S 424-011
 (1)  Install the side braces.
 NOTE: The installation of the lower side brace is the same as the
____
 upper side brace.

 (a)  
Lubricate pin assembly shanks, threads, washers and bearing surfaces with grease before you install the pin assemblies.

 (b)  
Set the upper side brace (3) for installation on the trunnion

 (7)
 of the nose landing gear.

 1)  Install the upper pin assembly which include the lube insert (6) and the bolt (5).
 (c)  Install the support bracket (10) of the cable pulley and the washer on the lower pin assembly.
 NOTE: The lower pin assembly have the lube insert (12) and
____
 the bolt (11).

 (d)  
Install the pin assembly (with the support bracket of the cable pulley) through the strut and the side brace (3) from the aft side of the strut.

 (e)  
Install the stirrup support bracket on the left bolt (11) only.

 (f)  
Install the washer (15) on the right side only, if removed.

 (g)  
Install the nut (2) on the pin assembly at the upper end of the side brace. 1) Tighten the nut 50 - 70 pound-feet (lube torque). 2) If it is necessary, loosen the nut to the nearest
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(150)