747-400
MAINTENANCE MANUAL
1480 BULKHEAD
SEE A
1480 STA
VALVE PRESSURE REDUCING POSITIONING BODY GEAR TRUCK
BACKUP RING
(2 PLACES)
RAPID RESPONSE
RELIEF VALVE
O-RING
A
Rapid Response Relief Valve Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-25
ALL ú ú 01 Page 402 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 494-026
(3)
Do this task: "Installation of the Door Locks on the Body Landing Gear" (Ref 32-00-30/201).
S 844-005
(4)
Decrease the pressure on the hydraulic system No. 1 (Ref 29-11-00/201).
S 844-006
WARNING: DECREASE THE PRESSURE ON THE ACTUATOR, THE LINES AND THE
_______ PRESSURE VALVE BEFORE YOU REMOVE THE RELIEF VALVE. THIS WILL PREVENT INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(5)
Open the bleed valve to decrease the pressure on the truck actuator, the lines and the pressure valve (Ref 32-13-15/401).
S 034-007
(6)
Remove the lockwire that hold the relief valve to the body of the pressure valve.
S 024-008
(7)
Loosen and remove the relief valve from the pressure valve.
TASK 32-13-25-404-009
3. Relief Valve Installation For The Pressure Reducing Valve (Fig. 401)
_________________________________________________________
A. Consumable Materials
(1)
D00288 Lubricant (Skydrol Assembly Lube) - MCS 352
B.
References
(1)
09-11-00/201, Towing
(2)
12-12-01/301, Hydraulic Systems
(3)
32-00-30/201, Landing Gear Door Locks
(4)
32-13-15/401, Body Gear Truck Positioning Actuator
(5)
32-13-24/401, Body Gear Truck Positioning System Hydraulic Fuse
(6)
IPC 32-13-16 Fig. 1
C.
Access
(1)
Location Zone
755 Body Landing Gear, LH
764 Body Landing Gear, RH
D.
Procedure
S 434-012
(1)
Install the new O-rings and the backup rings on the relief valve.
(a)
Lubricate the O-rings and the backup rings with Skydrol lubricant during the installation.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-25
ALL ú ú 01 Page 403 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 424-013
(2)
Install the relief valve into the body of the pressure valve.
(a)
Lubricate the seals and the rings with the Skydrol lubricant.
(b)
Tighten the relief valve to 500 - 520 pound-inches and tighten the lockwire.
S 864-027
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. THE AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THE THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS WILL CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(3)
Pressurize the hydraulic system No. 1 (AMM 29-11-00/201).
S 794-015
(4)
Examine for the hydraulic fluid leaks around the relief valve.
S 844-016
(5)
Permit approximately 1 to 2 pints of fluid to flow from the bleed valve of the truck actuator.
(a)
Bleed more fluid if there are bubbles in the system.
NOTE: If the flow stops, hold the manual bypass lever in a up
____ position for 2 seconds to set the fuse (station 1480 bulkhead).
S 434-017
(6)
Close the actuator port.
S 864-018 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 3(55)
