曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 2)  Adjust the linkage rod for the outboard door the amount you determined necessary to align the outboard door along the forward edge.
 3)  Close the body landing gear doors.
 4)  Determine the necessary shim thickness (View A-A, Figure 502) to set the stop at 0.002 - 0.015 inch
 (0.051 - 0.381 mm) clearance with the stop pad.
 (h) Adjust the inboard door:
 1)  Determine the adjustment to the linkage rod for the inboard door to fair the inboard door along the forward edge and inboard edge.
 NOTE: Find the mismatch at the stop (Views A-A and B-B,
____ Figure 502).
 2)  Move the ground release handle for the doors to the "Door Open" position to open the wheel well doors.
 3)  Adjust the linkage rod for the inboard door the amount you determined necessary to align the inboard door along the forward edge.
 4)  Close the body landing gear doors.
 5)  Determine the necessary shim thickness at view B-B, Figure 502) to set the stop so that is just touches the stop pad.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 36 Page 510 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
SEQUENCE VALVE LINKAGE ROD

Body Gear Wheel Well Door Open Position Adjustment
Figure 503 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 04 Page 511 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

VALVE 
INTERSECTION OF 
CENTER LINE OF 
(RIG PIN HOLE) POINT A  OF STOP SUPPORT AND LOWER EDGE HOLE FOR STOP 
BODY GEAR  FITTING 
WHEEL WELL 
CARRIER  OUTBOARD DOOR  FORWARD 
INBOARD 
STOP 

84.0 |1.0 INCHES 
BOLT 
LINKAGE 
ROD  ROD 
BRACKETS 
BODY GEAR 
WHEEL WELL 
BOLT  INBOARD DOOR 
A-A 

BODY GEAR
DOOR

C
Body Gear Wheel Well Door Open Position AdjustmentFigure 503 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 08 Page 512 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 6)  For the stop at view C-C, determine the adjustment that is necessary to bring the aft inboard edge of the inboard door into fair with the adjacent panel.
 7)  Move the ground release handle for the doors to the "Door Open" position to open the wheel well doors.
 8)  Install the shims and the stops at Views A-A and B-B to adjust the door to the amount that you determined is necessary.
 9)  For the stop at view C-C, install the shims and the stops to adjust the fair, or turn the stop pin, in or out, to get the adjustment you determined necessary and install the locking spring.
 (i)  Do the steps that follow to make sure the inboard and outboard door adjustments are correct: 1) Close the body landing gear doors. 2) Make sure the door mismatches at views A-A, B-B, and C-C
 (Figure 502) are in the tolerance. 3) Make sure that the stops touch the stop pads at view B-B and C-C (Figure 502). 4) Make sure there is a clearance of 0.002 - 0.015 inch
 (0.051 - 0.381 mm) between the stop and stop pad at view A-A (Figure 502).
 5)  Move the ground release handle for the doors to the "Door Open" position to open the wheel well doors.
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO
_______ INSTALL THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (j)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(66)