EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 04 Page 524 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
747-400 
MAINTENANCE MANUAL
 (p) (q) (r)  Adjust the forward outboard door stop at view D-D (Figure 505): 1) Retract the landing gear. 2) Find the necessary shim thickness that is needed at view D-D such that the stop pad just touches the door stop (Figure 505). 3) Extend the landing gear. 4) Install the shims and stop pad at view D-D that you determined are necessary (Figure 505).Retract the landing gear.Make sure that all of the door stops are in contact with the stop pads and that all of the doors are in fair.
 (s) (t)  NOTE: Write down the clearance dimension for the doors stops____ that do not touch the stop pads.Extend the landing gear and open the landing gear doors.If there is a clearance between the door stop and the stop pad at view A-A (Figure 502), shorten the linkage rod for the outboard door as follows:
 (u)  1) If the clearance at view A-A (Figure 502) is between 0.002 and 0.030 inch, turn the rod end fitting one-half turn to shorten the length of the rod. 2) If the clearance at view A-A (Figure 502) is between 0.031 and 0.054 inch, turn the rod end fitting one full turn to shorten the length of the rod.If there is a clearance between the door stop and the stop pad at views G-G or B-B (Figure 505), shorten the linkage rod for the shock strut inboard door as follows:
 (v)  1) Shorten the linkage rod for the shock strut inboard door by one half turn at a time until the door stop contacts the stop pad.Adjust the preload of the shock strut doors: 1) Turn one end fitting on the linkage rod for the shock strut inboard door one-half turn to shorten the length of the rod.
 (w)  2) Turn one end fitting on the linkage rod for the shock strut outboard door one full turn to lengthen the rod.Retract the landing gear.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 04 Page 525 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (x)  
Put the control lever for the landing gear in the OFF position.

 (y)  
Make sure that all of the door stops are in contact with the stop pads and that all of the doors are in fair.

 K.
Last Door Check (Figure 504)

 S 825-281
 (1)  Table 502 (for Figure 505) shows expanded tolerances which were permitted at delivery. Use these tolerances only if you cannot get the usual tolerances.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 04 Page 526 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE A
DOORSTOP SUPPORT (STA 1350 BULKHEAD)
A
SENSOR MOUNTING BRACKET
A
PRIMARY DOOR WARNING SENSOR (S408LH,S409RH) ALTERNATE DOOR WARNING SENSOR FWD(S428LH,S427RH)
A
SENSORS
TARGET
DOOR STOP SUPPORT
0.10 |0.03 INCH GAP INBD
0.10 |0.03
INCH GAP

BODY GEAR WHEEL WELL OUTBOARD DOOR SHOWN IN CLOSED POSITION
A-A
Body Gear Door Proximity Switch Gap Adjustment Figure 504
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-00
 ALL  ú ú 01 Page 527 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE A
BODY GEAR
BODY GEAR WHEEL WELL
WHEEL WELL OUTBOARD DOOR
INBOARD DOOR WING GEAR WHEEL WELL INBOARD DOOR
BODY GEAR 
SHOCK STRUT 
OUTBOARD DOOR 
F  E 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(72)