C.
References

 (1)  
AMM 32-00-30/201, Landing Gear Door Locks

 (2)  
AMM 32-14-03/601, Body Gear Wheel Well Door Safety Bar

 D.
Access

 (1)  
Location Zone 753 Body Landing Gear Forward Inboard Door, LH 763 Body Landing Gear Forward Inboard Door, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-03
 ALL  ú ú 01 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E. Procedure
 S 224-006
 (1)  
Examine the worn parts and the fittings for the approved worn areas (AMM 32-14-03/601).

 S 424-007

 (2)  
Install the safety bar.

 (a)  
Install the slide pad (13) on the shoe (12) if it was removed, with 4 bolts (8) and the washers (9).

 NOTE: Use only new bolts and install the Lockwire on the
____
 bolts.

 (b)  
Use the bushing (5), the washers (6 and 10), the bolt (7) and the nut (11) to connect the shoe (12) to the safety bar.

 (c)  
Put the slide end of the safety bar into the slide rails on the inboard door.

 (d)  
Install two hinge pins (4), the washers (3), and the cotter pins (2).

 (e)  
Apply a layer of grease on the safety bar (1) in the area where the tire touches during the alternate extension.

 S 094-012
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 094-013

 (4)  
Do this task: "Removal of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-14-03
 ALL  ú ú 01 Page 404 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 BODY GEAR WHEEL WELL DOOR SAFETY BAR - INSPECTION/CHECK
_______________________________________________________
 1.  General_______
 A. This procedure has one task:
 (1)  
The examination of the fit for the safety bar bearings, the bolt, the pad and the bushings.

 B.
You must remove the safety bar to do the inspection.

 TASK 32-14-03-206-001
 2.  Body Gear Wheel Well Door Safety Bar Examination for Worn Areas (Fig. 601)_______________________________________________________________
 A. References
 (1)  
12-21-01/301, Landing Gear

 (2)  
IPC 32-14-03 Fig. 1

 (3)  
32-14-03/401, Body Gear Wheel Well Door Safety Valve

 B.
Access

 (1)  
Location Zone
 754 Body Landing Gear Door, LH
 764 Body Landing Gear Door, RH

 C.
Procedure

 S 026-002
 (1)  
Remove the safety bar (Ref 32-14-03/401).

 S 226-003

 (2)  
Examine the worn limits of the safety bar bearings, the bolt, the pad and the bushing.

 (a)  
Measure the parts if it necessary and compare the measured dimensions to the limit demensions.

 (b)  
If the part is not in the tolerance, repair or replace if it is necessary.

 (3)  
Examine the moved areas of the safety bar for damage or worn areas.

 S 116-005

 (4)  
Remove all collected rubber with solvent and lubricate the surface with grease (Ref 12-21-01/301).

 (5)  
Install the safety bar (Ref 32-14-03/401).

 S 216-004
 S 426-006
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(88)