(7)
Hold the manual bypass lever in a up position for 2 seconds to set the truck position (Ref 32-13-24/401).
S 844-019
(8)
Open the actuator bleed valve.
(a)
Permit approximately 10 cubic inches of fluid to set the fuse.
(9)
Tighten the bleed valve and the lockwire.
S 614-021
(10)
Examine the hydraulic reservoir level and fill it if it is necessary (Ref 12-12-01/301).
S 434-020
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-25
ALL ú ú 05 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 094-028
WARNING:_______ YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE
QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS
CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(11)
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (Ref 32-00-30/201).
S 094-029
(12)
Do this task: "Removal of the Door Locks from the Body Landing Gear" (Ref 32-00-30/201).
S 864-023
(13)
Remove the hydraulic system No. 1 power if it is not necessary (Ref 29-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-25
ALL ú ú 01 Page 405 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
BODY LANDING GEAR AXLE SLEEVE - REMOVAL/INSTALLATION
____________________________________________________
1. General
_______
A. This procedure has two tasks:
(1)
The removal of the axle sleeve from the axle for the body landing gear
(2)
The installation of the axle sleeve on the axle for the body landing gear.
B.
The axle sleeve and the brake housing bushing have an interference fit on the landing gear axle. It is necessary to use temperature differential procedures to remove or install these components.
TASK 32-13-26-004-001
2. Body Landing Gear Axle Sleeve Removal (Fig. 401)
_____________________________________
A. General
(1)
The axle sleeve cannot be removed if the brake housing bushing is on the axle.
(2)
This task includes the steps to remove the brake housing bushing.
(3)
It is not necessary to remove the wheel truck to do this task.
B.
Special Tools and Equipment
(1)
G32010 - Puller Equipment, Axle Sleeve
C.
Standard Tools and Equipment
(1)
Heat Blanket - Electrical (300°F maximum)
(2)
Thermometer - Surface Measurement (0° - 350°F)
D.
Consumable Materials
(1)
G00829 Ice - Dry (Commercial Grade)
E.
References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 32-00-30/201, Landing Gear Door Locks
(3)
AMM 32-41-15/401, Landing Gear Brake Unit
(4)
AMM 32-42-04/401, Antiskid Transducer
(5)
AMM 32-45-01/401, Main Gear Tire/Wheel Assembly
F.
Access
(1)
Location Zone
755 Body Landing Gear, LH
765 Body Landing Gear, RH
G.
Prepare for the Procedure
S 494-002
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Install the ground locks in all landing gear (AMM 09-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 3(56)
