(1)
 Put the tape (1) in position and install the latch (2) with the screws (3).

 (2)
 Put the support (7) in position and install the screws (5) with the washers (6).

 (3)
 Put the baby nursing table (4) in position and install the screws (8) to secure the hinge to the lavatory rear wall.

 EFF : ALL
25-45-25Page 408

 **ON A/C ALL
 Subtask 25-45-25-420-051
 C. Installation of the Baby Nursing Table
 (Ref. Fig. 402/TASK 25-45-25-991-002)

 (1)
 Put the latch (1) in position and install the screws (2).

 (2)
 Put the support (8) in position and install the screws (6) with the washers (7).

 (3)
 Put the baby nursing table (4) in position and install the screws (3) to secure the hinge to the lavatory rear wall.

R **ON A/C 001-049, 051-058, 101-101,
 Subtask 25-45-25-710-050
 D. Operational Test of the Baby Nursing Table (For Lavatory A only)
 (1) Baby nursing table installed on the lavatory L/H side wall. (Ref. Fig. 401/TASK 25-45-25-991-001)
 (a)
 Open and close the baby nursing table (1) and make sure that the table locks correctly in the closed position, if necessary adjust as follows;

 (b)
 Loosen the screws (7).

 (c)
 Adjust the lacht (6) until the baby nursing table (1) locks correctly.

 (d)
 Tigten the screws (7).

 EFF : ALL
25-45-25Page 409

R **ON A/C 059-099, 102-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 25-45-25-710-050-A
 D. Operational Test of the Baby Nursing Table (For Lavatory A only)
 (1) Baby nursing table installed on the lavatory rear wall (Ref. Fig. 401A/TASK 25-45-25-991-001-A)
 (a)
 Open and close the baby nursing table (4) and make sure that the table locks correctly in the closed position, if necessary adjust as follows;

 (b)
 Loosen the screws (3).

 (c)
 Adjust the latch (2) until the baby nursing table (4) locks correctly.

 (d) Tigten the screws (3).
 **ON A/C ALL

 Subtask 25-45-25-710-051
 E. Operational Test of the Baby Nursing Table
 (1) Baby nursing table installed on the lavatory rear wall (Ref. Fig. 402/TASK 25-45-25-991-002)
 (a)
 Open and close the baby nursing table (4) and make sure that the table with the hook (5) locks correctly in the closed position, if necessary adjust as follows;

 (b)
 Loosen the screws (2).

 (c)
 Adjust the latch (1) until the baby nursing table (4) locks correctly.

 (d)
 Tigten the screws (2).

 EFF : ALL
25-45-25Page 410

 5. Close-up
________ Subtask 25-45-25-862-050
 A. De-energize the ground service network (Ref. TASK 24-42-00-862-001).
 EFF : ALL
25-45-25Page 411

 LINING - REMOVAL/INSTALLATION
_____________________________
 TASK 25-45-26-000-001
 Removal of the Lining

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001  Energize the Ground Service Network from the External Power R 25-45-38-000-001 Removal of the Wash Basin 25-45-26-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 25-45-26-861-050

 A. Aircraft Maintenance Configuration
 (1) Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 Subtask 25-45-26-010-050
 B. Get Access R (1) Remove the wash basin assembly (Ref. TASK 25-45-38-000-001).
 4. Procedure
_________
 Subtask 25-45-26-020-050

 A. Remove the Lining
 (Ref. Fig. 401/TASK 25-45-26-991-001)

 (1) Remove the screws (4), the washers (3) and if installed the spacers (2).
 EFF : ALL
25-45-26Page 401

 Lining
 Figure 401/TASK 25-45-26-991-001
 EFF :  ALL  25-45-26 Page 402 
Feb 01/98
 CES 

 (2)
 Remove the lining (1).

 (3)
 Remove the rollers (6), the screws (5) and the roller bracket (7).

 EFF : ALL
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(129)