曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  Subtask 25-33-41-420-059-B 
R  D. Installation of the Galley Unit 
R  (1) Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-21-
11-911-001). 
R  (2) Install the Lower Attachments 
R  (Ref. Fig. 409/TASK 25-33-41-991-004) 
R  (a) Turn the eccentric bushes (58) against the eccentric plugs (57) 
R  until the holes align and the galley touches all floor 
R  hardpoints, if necessary. 
R  (b) Install the plates (56). 
R  (c) Apply the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-002) to 
R  the threads of the screws (54). 
R  (d) Install the screws (54) and the washers (55). 
R  (e) Put the floor seals (74) in position. 
R  (f) Put the cover-seal (73) in position and install the screws (72). 
R  (g) Put the seals (76) and (78) in position and install the screws 
R  (75) and (77). 
R  (h) Put the seals (80), (82), (84), (86) and (88) in position and 
R  install the screws (79), (81), (83), (85) and (87). 
R  (i) Put the seals (89) and (91) in position and install the screws 
R  (90) and (92).

 CES

R  (j) Put the cover-seal (95) in position and install the screws (94). 
R  (k) Put the guides (93) and (96) in position and install the screws 
R  (97). 
R  (l) Put the guides (70) and (99) in position and install the screws 
R  (71) and (98). 
R  (3) Install the Upper Attachments 
R  (Ref. Fig. 405B/TASK 25-33-41-991-014-A, 409/TASK 25-33-41-991-004) 
R  (a) Put the tie rods (53) in position and install the quick-release 
R  pins (52). 
R  (b) If necessary, remove and adjust the tie rods (53): 
R  1_  Remove and discard the lockwire.
R  2_  Loosen the locknut.
R  3_  Adjust the rod end so that the quick-release pins (52) can be
R  installed easily. 
R  4_  Tighten the locknut.
R  5_  Make sure that the rod end is in a safe condition.
R  6_ Safety the locknut with the lockwire,MISCELLANEOUS (Material
 No. 19-010). 
R  (c) Put the access panels (100) in position and install the screws 
R  (101). 
R  (d) Put the pelmet (111) in position and install the bolts (112). 
R  (e) Put the pelmet covers (49) in position and tighten the studs 
R  (48). 
R  (4) Install the Supply Connections 
R  (Ref. Fig. 402C/TASK 25-33-41-991-006-B) 
R  WARNING : MAKE SURE THAT THE POTABLE WATER SYSTEM IS DEPRESSURIZED. A_______ 
R  PRESSURIZED SYSTEM CAN CAUSE INJURY TO PERSONS WHEN THEY DO 
R  WORK ON IT. 
R  (a) Remove the blanking plugs from the disconnected line ends.

 

R  (b) Connect the exhaust air hose (29) to the exhaust air connection 
R  (31) and install the clamps (30). 
R  (c) Connect the ventilation hose (34) to the air supply connection 
R  (32) and install the clamp (33). 
R  (d) Connect the waste water hose (35) to the waste water connection 
R  (37) and install the clamps (36). 
R  (e) Connect the potable water hose (40) to the fresh water connection 
R  (38) and fasten the nut (39). 
R  (f) Put the access panel (28) in position and install the screws 
R  (27). 
R  (5) Install the Pedestal Panel 
R  (Ref. Fig. 402C/TASK 25-33-41-991-006-B) 
R  (a) Carefully put the pedestal panel (22) in position. 
R  (b) Install the screw (21) and the washer (20). 
R  (c) Install the screws (26) and (25). 
R  (d) Install the screws (23) and the washers (24). 
R  (6) Connect the Electrical Connections 
R  (Ref. Fig. 401C/TASK 25-33-41-991-022-B) 
R  (a) Put the bonding straps (15) in position and install the washers 
R  (16), the bolts (17) and the nuts (14) (Ref. TASK 20-28-00-912-
004). 
R  (b) If necessary install the stud (1) and put the spacer (2) in 
R  position. 
R  (c) Put the clamps (3) in position on the cables and install the nuts 
R  (5) with the washers (4). 
R  (d) Put the clamps (10) and (13) in position on the cables and 
R  install the bolts (11) with the washers (12).

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(35)